搜索资源列表
LED
- 【实验题目】 LED闪烁发光 【实验目的】 掌握定时器T0或T1的简单用法。 【硬件接法】 P1.1控制LED,低电平点亮。 【实验步骤】 ISP下载开关扳到“00”,用Flash Magic软件下载程序文件“Timer.hex”,运行。 【运行效果】 LED亮200ms,灭800ms,反复循环。
Multistatewaterlights
- 多种状态的流水灯课程设计:LED闪烁种类: ①、单个LED顺时针闪烁 ②、LED顺时针递增亮 ③、红灯LED和绿灯LED两者循环交替闪烁 ④、对角线LED顺时针循环闪烁 ⑤、所有LED同时闪烁 ⑥、单个LED顺时针闪烁,再逆时针闪烁 ⑦、对角线LDE顺时针闪烁,再逆时针闪烁 ⑧、LED顺时针递增亮,再逆时针递增亮 ⑨、两个LED顺时针闪烁 -Multi-state water lights
Led
- 用DELPHI模拟LED屏下的那种文字特效怎么做啊? 如: 左移入 右移入 上移入 下移入 左展入 右展入 上展入 下展入 横向展开 横向闭合 纵向展开 纵向闭合 水平百叶窗 垂直百叶窗 闪烁 同时显示-DELPHI simulation of LED screen with the kind of text effects, u
LED
- 用DELPHI模拟LED屏下的那种文字特效怎么做啊? 如: 左移入 右移入 上移入 下移入 左展入 右展入 上展入 下展入 横向展开 横向闭合 纵向展开 纵向闭合 水平百叶窗 垂直百叶窗 闪烁 同时显示-DELPHI simulation of LED screen with the kind of text effects, u
GPIO_RVMDK
- 本源码为STM32的GPIO使用例程,主要演示GPIO的使用。开发环境realviewMDK。 程序通过按键对应的引脚的电平是否被拉低来判断按键是否被按下,如果按键被按下,则相应的LED闪烁一次。-The source code for the STM32' s GPIO use of routine, the main demonstration GPIO use. Development environment realv
stc2051
- STC 2051示范例子。 1.LED闪烁。 2.串口每秒钟输出一个字符。-STC 2051 Demo
led
- 源码是控制一排led灯闪烁,源码已经调通。-Source code is to control a row of led lights flashing, source code has been transferred pass.
LED
- LED闪烁发光 使用于ARM LM3S2110开发模板-very good
Blinky
- c8051f340 blinky led闪烁,头文件等等,非常实用-c8051f340 blinky led blinky head files etc. useful for ee
LED
- LED闪烁通过单片机I、O口控制led灯的闪烁 利用单片机的定时器来实现时间的控制-LED flashes through the microcontroller I, O port control led lights flashing MCU timer using the time control to achieve
led
- 使用89c51单片机,配合595使LED闪烁,时间间隔为1ms-Using 89c51 microcontroller with 595 to make LED flash, the time interval of 1ms
led
- 基于TMS320VC5416的定时器编程,DSP工作在8MHZ主频,定时器分频系数为15,通过DSP通用I/O引脚控制指示灯闪烁,指示灯每秒闪烁1次。-TMS320VC5416 timer based programming, DSP working in 8MHZ frequency, the timer frequency factor of 15, through the general-purpose DSP I/O pin c
timer2
- stm8的timer2例程,利用溢出中断,实现1s,LED闪烁一次-stm8 the timer2 routine, the use of overflow interrupt, to achieve 1s, LED blink once
STM32.RAR
- STM32所有开发例子程序.RAR GPIO_out 8个led闪烁 注意:接跳线D1_CS, D2_CS, LCD 液晶上显示英文字符 LCD_汉字 液晶上显示汉字 LCDBMP 液晶上显示图片 ADC 液晶上显示采的电压值 SDcard SD卡上建立一个文件 UART 串口发送字符在液晶上显示 RTC 液晶上显示时间 ExIRQ 外部中断,S2给中断信号 Timer 定时 C
1
- 本实验的实现功能:LED闪烁.适用于zigbee开发板。-In this study, the implementation features: LED flashes. For zigbee development board.
LED
- 用单片机实验板做的一个 LED 闪烁的简单试验-MCU Board used to do a simple test LED flashing
led-for-LM3S811
- 为LM3S811嵌入式单片机设计的led循环闪烁的程序-For LM3S811 embedded microcontroller led circulation flickering program
1-LED
- LED闪烁 的C编程程序说明 很简单哦-LED flashing program that is simple C programming Oh
LED-flash-timer--cc2430
- 物联网必学芯片:cc2430 实验例程:利用定时器实现LED闪烁 虽然源程序可以用VC打开,但工程的开发环境应为IAR Embedded Workbench-Things will learn chips: cc2430 experimental routine: use timer, LED flash can be used although the VC open source, but the engineering d
LED
- LED闪烁 LPC2114入门学习程序,简易流水灯-LED flash LPC2114 introductory learning program, simple water lamp