搜索资源列表
time1.asm
- 本程式以計時方式掃描驅動,以P0.0為0.05秒的閃爍, P1到P3分別為秒分時的輸出 -program to the scanning of driving time to P0.0 of 0.05 seconds flickered. P1 to P3 were seconds TDM output
PIC_STUDY
- 完整的PIC学习程序示例 软件功能: RT1602C驱动 UART串口输出,波特率为19200 按键扫描: 键1控制LCD的显示状态,接收状态或是发送状态 键2循环控制UART将要输出的子串口 AD转换功能 UART串口接收中断 TIME1定时器中断 具体请参考硬件连接图-integrity of the learning process software examples : RT1602C
time1-10ms
- 主要用于在单片机中可以随时变更的延时操作,采用单片机的定时器实现
TIME1.C
- 用四位数码管显示时间源程序1
dlq
- 教学打铃系统 变量定义 scl bit p3.3 sda bit p3.2 time0 equ 30H 秒Y time1 equ 31H 时Y time2 equ 32H 分Y time3 equ 33H 十毫秒次数控制Y disp_t00 equ 35H 秒个位Y(右) disp_t01 equ 36H 秒十位 disp_t10 equ 37H 分个位 disp_t11 equ 38H 分
time1
- 电子时钟,可以通过M键转换功能,其中包括日期,时间,秒表等功能。
Time1
- s3c2410 pwm 不用注册流,定时器1的使用
Time1
- 本程序实现系统时间查看.-system to examine.
time1-example
- AVR定时器1最简例程,注解非常详细,对于初次使用AVR定时器非常有用
Examples
- STM32 demo板的例程,其中包括AD,USART ,TIME1,TIME,CAN,DMA,FLASH,SPID等例程序,适合新手学习入门
Time1
- 本程序实现系统时间查看.-system to examine.
PIC_STUDY
- 完整的PIC学习程序示例 软件功能: RT1602C驱动 UART串口输出,波特率为19200 按键扫描: 键1控制LCD的显示状态,接收状态或是发送状态 键2循环控制UART将要输出的子串口 AD转换功能 UART串口接收中断 TIME1定时器中断 具体请参考硬件连接图-integrity of the learning process software examples : RT1602C
time1-10ms
- 主要用于在单片机中可以随时变更的延时操作,采用单片机的定时器实现-Mainly used in single-chip microcomputer can be changed at any time delay operation, the use of single-chip timer realize
TIME1.C
- 用四位数码管显示时间源程序1 -With four digital tube display time source 1
dlq
- 教学打铃系统 变量定义 scl bit p3.3 sda bit p3.2 time0 equ 30H 秒Y time1 equ 31H 时Y time2 equ 32H 分Y time3 equ 33H 十毫秒次数控制Y disp_t00 equ 35H 秒个位Y(右) disp_t01 equ 36H 秒十位 disp_t10 equ 37H 分个位 disp_t11 equ 38H 分
timer1
- time1编程模块 直接嵌入就可以使用 pic平台-time1 programming module can be directly embedded platform using pic
time1
- AVR单片机定时器2的异步操作功能用作实时时钟的效果。同时讲解了BASCOM-AVR中关于时钟硬件配置方面的语句。在BASCOM的概念里主要分为SOFT和USER两大类时钟产生的方法。利用芯片定时器的异步功能称为软时钟,利用专用时钟芯片则要用户自己编写相应的处理程序,所以称USER。但不管采用哪种方式,相关的中断服务程序或是函数都要支持DATE$和TIME$以及_sec , _min , _hour, _day , _month , _
Time1-Test
- STM32定时器time1详细使用源码,经过测试准确无误-STM32 timer tim1 detailed use of the source code, tested accuracy
stm8
- 使用STM8配置TIME1、UART1、UART3,在STM8S007单片机控制使用空气温湿度传感器(SHT10)、温度传感器(DS18B20)(Using STM8 configuration, TIME1, UART1 and UART3, the STM8S007 microcontroller controls the use of air temperature and humidity sensors (SHT10) and
time1和time3 16khz_pwm占空比变化
- ZIGBEE CC2530 time1和time3 输出6路 16khz pwm,占空比可调(ZIGBEE CC2530 time1 and time3 6 16KHz output PWM, adjustable duty ratio)