搜索资源列表
adda
- 文件名称: A/D实验--采样、存储和显示实验.ASM 文件标识: none 适用器件: 89C51 ①ADC0809的片选CS1连A15,RAM6116的片选CS3连A14。 ②要求在ADC0809的输入端加上不同的模拟信号,通过键盘输入ADC0809的通道号并启动A/D转换, 采集N个(如N=256)数据存入外部RAM中,打开XDATA窗口,检查实验结果。 注意:①在进行A/D采样前,应先检查ADC0809的
qincb
- 这是三个程序 第一个是获取电压的labview程序 第二个时万用表34401Amultimeter的labview程序,第三个时如何控制开关电路的labview程序
GPIO
- IO口测试程序 轮流置高和低,可接LED灯测试或用万用表测试,或单独设定电平值-IO port test program Rotation values of high and low, the LED lamp test with a multimeter to test which can be accessed or a separate set of level values
adc
- 这个代码是用keil4.22编译成功的。实现的功能是通过dma来读adc,然后通过dma的中断里用串口打印出来。直接显示adc上的电压,要比万用表精确。代码里面总共用过dma,中断,查询这三种方式实现读值。比较强大。-stm32f103vbt6, adc,dma ,usart,
LTC1865
- 用AT89S52和AD LTC1865开发的直流万用表。-AT89S52 and AD the LTC1865 development of DC multimeter.
VirtualInstrument
- FLUKE 45双显示数字万用表应用程序,串口连接。可进行数据采集并具有简单数据分析功能,包括最值、均值、方差等。运行环境-.Net 2.0-FLUKE IS 45 dual display digital multimeter application, serial connection. Data collection and simple data analysis capabilities, including the most
dian-zu-se-huan-dui-zhao-biao
- 电阻色环对照表。做电子设计常需要对电阻的大小进行测量,如果你知道了对照表就不用用万用表测量了,很方便-Resistor color ring table. Electronic design often need to measure the size of the resistance, if you know the table is not measured with a multimeter, it is convenient
wanyongbiao
- 基于89C52的万用表设计代码,Keil uVision4编译器。-89C52-based multimeter design code, the Keil uVision4 compiler.
AD
- AD转换算法 实现单片机当电压万用表 超级好的程序-AD conversion algorithm the microcontroller when the voltage multimeter super good program
GPIO
- 轮流置MSP430的高和低,可接LED灯测试或用万用表测试,或单独设定电平值-Take turns to buy MSP430 with high and low, may meet LED lamp test or using a multimeter to testing, or separate set level value
fluke8800-Labview
- 利用labview控制fluke8800数字万用表,连续测量电流、电压等曲线,显示并保存结果。-use labview control fluke8800 digital multimeter and continuous measurement of current, voltage curve, display and save the results.
shuzidianyabiao
- 利用单片51机设计简单实用的万用表,利用单片51机设计简单实用的万用表。-Monolithic 51 machine design is simple and practical multimeter.
wanyongbiao-Multisim
- 这是 我做模拟电子课程设计时的,利用Multisim所设计的万用表总设计图,仅是设计图,具体的还需要您来仿真。-This is the design of the I do analog electronic curriculum design, the use of Multisim the multimeter total design, only the design you need to emulate. Thank you
2812ADsample
- AD采样频率为10K,序列发生器SEQ1和SEQ2级联成一个16通道的序列发生器,采样模式采用顺序采样。利用通用定时器T1的周期中断事件来启动AD转换。ADCINA0和ADCINB0为参考电平,实际的电压值分别为0.420和1.653,由于每个板子的具体特性稍有不同,请用万用表自行测量参考电压值。此例程对ADCINA0、ADCINA1、ADCINB0、ADCINB1四个通道进行连续10次的采样,然后对各个通道的10个采样值进行排序,滤波
DianYaBiao
- 利用PSOC实现电压表的功能,测试电压,误差在允许范围内,以万用表测试到的为准-PSOC V
elecfans.com-wan-yong-biao
- elecfans.com数字万用表 电路图,可以用以学习-elecfans.com digital multimeter circuit diagram
chengxu
- 本次设计用单片机芯片AT89s52设计一个数字万用表,能够测量交、直流电压值、直流电流、直流电阻,四位数码显示。此系统由分流电阻、分压电阻、51单片机最小系统、显示部分、报警部分、AD转换和控制部分组成。-The design of MCU chip AT89s52 to design a digital multimeter, capable of measuring AC, DC voltage, DC current, DC re
AD
- 使用AD单通道多次转换,采集P6.0输入的模拟电压值(变化范围:0~将P6口输入的模拟电压AD转换后,从P4、P5口连接的数码管输出。 使用AD单通道多次转换,采集P6.0输入的模拟电压值(变化范围:0~3.3V),转换为数字量。 建立二维数组和通过顺序查表的方法得出采集回来的电压值。然后通过数码管显示当前电压值,显 示跟随输入的模拟电压的变化。由于只有两位数码管,故显示电压值精确到小数点后一位,如当前 输入电压2
dianyabiao
- 使用51单片机做的简易的万用表,可以用来测量直流电压及直流电流等内容-Using 51 single-chip to do the simple multimeter, can be used to measure DC voltage and DC current etc.
ad-for-voltage
- 基于zigbee cc2530的ADC做电压表实例,参考电压为AVDD_soc,通过与万用表的比对,误差在+-0.02V。注释详细-Zigbee cc2530 ADC the voltmeter instance, the reference voltage is AVDD_soc, by with multimeter comparison, errors in+-0.02V. Notes in detail