搜索资源列表
7PWM-Test
- 这个程序主要运用于四路pwm波生成以及三路互补PWM波输出-pwm generation
spwm
- 基于TMS2812的SPWM代码，输出的PWM波形是互补的两路信号，且设有死区。-TMS2812' s SPWM based code, the output of the PWM waveform is complementary to two signals, and with dead.
pwm1
- STM32在IAR环境下操作定时器输出互补模式的PWM的程序源码。-STM32 mode PWM operation timer output complement each other in the IAR environment program source code.
TMS320F28335_PWM_dead
- 针对TI公司的TMS320F28335这一款DSP的ePWM模块开发出的程序。该程序的功能是：在ePWM3A和ePWM3B上输出带死区的互补PWM波形-Develop procedures for TI' s TMS320F28335 This is a the DSP' s ePWM module. The function of the program is: complementary PWM waveform out
EvPwm02
- 2812 PWM程序：初始化EVA，使得PWM1和PWM2输出互补的周期为1KHz的PWM波，占空比初始化为10 ，死区时间为4.27us-2812 PWM procedures: Initialize EVA makes PWM1 and PWM2 output complementary cycle 1KHz PWM wave, 10 duty cycle initialization, deadtime 4.27us
M051-PWM
- M051的PWM呼吸灯输出以及半桥互补输出，寄存器操作，接近C51程序-M051 PWM respiration lamp and half-bridge complementary output
danxiangqiaoshinibian
- 基于stm32的单相桥式逆变，两路互补型PWM输出正弦50Hz波形-Stm32-based single-phase bridge inverter, two complementary 50Hz sine wave PWM output
SVG_flash_20130618
- 运行环境为CCStudio v3.3。该程序为DSP TMS320F28335 初始程序，已经初始化EPWM，只要相应得改动输出比较寄存器就可以得到6组波形互补加死区控制的PWM波。-The program for the DSP TMS320F28335 initial program, has been initialized EPWM, may change as long as the corresponding output
STM32f103-
- STM32f1o3单片机输出四路互补的PWM波形子程序，可作为电机控制及全桥开关电源的开关管驱动，程序已经示波器调试通过-STM32f103 microcontroller, four road complementary PWM waveform output can be used as a motor control and the whole bridge switching power supply switch tube d
pwm
- PWM VHDL程序，双路互补输出,精度占空比可调-PWM VHDL program, dual complementary output, precision adjustable duty cycle
3.26-PWM
- 输出互补周期可调占空比可调死区可以调节的pwm波形-Complementary cycle adjustable output adjustable duty cycle can be adjusted deadband pwm waveform
2load-PWM
- msp430单片机输出两路互补，带死区的PWM波形-MSP430 MCU output two complementary PWM
搞定_ STM32 TIM1输出互补波形 加 详细中文注释
- 搞定_ STM32 TIM1输出互补波形 加 详细中文注释(STM32 output complementary PWM wave)
PWM1
- 输出两路pwm波,而且两路波形互补对称，需要的可以下载(Output two PWM waves, and the two waveform complementary symmetry)
1 PWM高级定时器互补输出
- STM32高级定时器实现互补输出通过RC震荡电路输出正弦交流电，实现直流转交流。两个通道之间存在一个死去时间。(The STM32 advanced timer implements complementary output through the RC oscillating circuit to output sinusoidal alternating current to achieve direct flow communic
stm8_play_wav_by_wang@2017-7-7
- 通过串口将音频数据发往stm8，stm8通过互补的pwm通道输出BTL推动喇叭播放音乐。wav格式为16K采样8bit模式，附带了xp的录音机可以进行格式转换。(Through the serial port to the audio data sent to stm8, stm8 through the complementary pwm channel output BTL to promote the speaker to pla
demo_pwm
- STM32F103ZET6开发板，死区时间的研究,定时器1输出互补波形(STM32F103ZET6 development board, dead zone time study, timer 1 output complementary waveform)
test
- stm32输出互补的带有死区的pwm波形(STM32 output complementary PWM wave with dead zone)
STM32F0XX教程+例程源码
- STM32F0XX教程+例程源码 教程目录： 工程篇：搭建KEIL-MDK开发平台及制作MDK工程文件模板.pdf 资料篇-NUCLEO-072RB开发板特性讲解及资料准备.pdf 初级教程篇：按键(中断方式)实现24C04存储器内容读写.pdf 初级教程篇：实现一个LED灯(软件延时 systick定时器).pdf 中级教程篇：利用SPI总线构建NUCLEO-072RB和NUCLEO-302RB双机处理系统.pdf 中级教程篇：利用
PWM互补死区输出
- 在STM32开发平台下，通过定时器的时钟配置，进行的PWM互补带死区的方波对电机进行控制。(Under the STM32 development platform, the PWM complementary square wave with dead zone is used to control the motor through the clock configuration of the timer.)