搜索资源列表
SN3188_20080714
- SN3188的单片机程序，有跑马灯和呼吸灯效果，可以作为参考移植到其他的系统上-SN3188 microcontroller procedures, there is Marquee and respiratory effects of light can be used as reference to migrate to other systems on
breathLight
- s12xs芯片实用的呼吸灯程序，灯的亮度随着时间变化，默认PORTB接了led灯-chip s12xs practical procedures to breathe light, lamp brightness changes with time, the default then the led lights PORTB
SN3188_led_spi
- 基于MTK平台实现的呼吸灯芯片-矽恩SN3188的SPI驱动代码，启用GPT timer使呼吸效果更佳。-MTK platform based on the respiratory light chip- SI-EN SN3188 SPI-driven code, and enable the GPT timer to make breathing better effect.
multifunctionalclock
- 1.八段数码管的显示；2、A/D的转换(毫伏表)；3、时钟显示及时间设定；4、呼吸灯；5、按键的设置功能及按键声音；6、A/D的报警功-1. Ba Duan digital tube display 2, A/D conversion (mV table) 3, the clock display and time settings 4 respiratory light 5, buttons and button set fe
huxideng_f020_OK
- 一个简单的呼吸灯程序，用c8051f020单片机，采用pwm调整占空比来实现-A simple breathing light program, with c8051f020 single chip, using pwm adjust the duty cycle to achieve
蓝牙调led亮灭
- 蓝牙控制灯的亮灭，想多少亮度都可以实现它，(Bluetooth control lights go out, you want to achieve how much brightness you can achieve it,)
RGB_LED_M051
- 利用PWM驱动RGB管脚的LED等，并呼吸效果(Use PWM to drive the RGB pin of LED, etc., and breathe the effect)
光敏传感器控制呼吸灯的明暗程度
- 光敏传感器的使用，使用STM32单片机，控制灯的亮的程度。(The use of photosensitive sensors, the use of STM32 microcontroller, control the brightness of the light.)
SHT2x-master（温度湿度）
- 此代码可用于arduino中，以温湿度为变量控制led灯变换或设置呼吸灯(This code can be used in Arduino, with temperature and humidity as variables to control the LED light conversion or set the breathing lamp)
新建 永中文字
- 关于控制LED呼吸渐变的效果，采用STC89C54单片机实现(On the control of LED breathing gradient effect, using STC89C54 MCU)
Breathing lamp
- 单片机采用脉冲宽度调制（PWM）方式控制LED灯亮度;通过软件模拟pwm.在一定的频率的方波中，调整高电平和低电平的占空比，实现LED灯亮度控制。(SCM uses pulse width modulation (PWM) mode to control the brightness of LED lights; through software simulation pwm. in a certain frequency square
呼吸灯
- 采用定时器中断模仿生成PWM波，形成呼吸效果(Analog PWM wave generated by timer interrupt to form respiratory effect)
呼吸灯
- 基于ARM Cortex-M4F(TM4C123)单片机 【功能】任选一个LED灯，4秒内从全灭到全亮，再从全亮到全灭，亮度变化至少20阶，循环反复（呼吸灯效果）。(Breathing light ---------Based on ARM Cortex-M4F (TM4C123) microcontroller)
3. 手机端APP通过Wifi控制LED呼吸灯状况
- 手机端通过TCP的app控制灯光亮度等(The mobile terminal controls lighting brightness through TCP's app)
Exp4TZ
- 用于实现LED的呼吸灯,通过FPGA调试成功,用了PWM的原理(About the LED of PWM)
LIGHT
- STM32神舟1号开发板实现通过2个按钮中断来控制流水灯和呼吸灯效果切换(STM32 Shenzhou 1 development board to achieve 2 buttons to interrupt the control of water lamp and breathing lamp effect switching)
lab2_breathingLED
- 通过vhdl语言，通过进行wpm调制，在小脚丫实验板上面实现呼吸灯，可调周期与脉宽(Through the VHDL language, through the WPM modulation, the breathing lamp can be realized on the small foot board, and the cycle and pulse width can be adjusted.)
move
- stm8实现流水灯，变频闪烁等功能，呼吸灯，跑马灯。(Stm8 realization of running water lamp)
MFC 测试 呼吸灯等系统API
- 让屏幕渐变亮度，修改RGB值来实现的变化(let sceen turn light or dark.)
Breathing LED
- msp430g2553 launchpad的可控呼吸灯程序，只有一个按键所以只能调快(Msp430g2553 launchpad's controllable breathing lamp program has only one button, so it can only be adjusted quickly)