搜索资源列表
GPIO-example
- GPIO_LCM.c 该文件是GPIO模拟时序，实现SPI协议的代码。 GPIO.pdf 该文件是C6713的GPIO连接LED和LCM模块的原理图，至于C6713的其他部分（如SDRAM、FLASH等）和部分控制信号、电源信号都略去-application example for GPIO on DSP
M8_595
- 单片机,avr单片机,atmega8,带仿真,74hc595 驱动,非spi 内嵌驱动,模拟时序-Microcontroller, avr microcontroller, atmega8, with simulation, 74hc595 driven, non-spi embedded driver, analog timing
EXP7-DS18B20
- 温度测量文件，使用DS18B20模拟时序测量温度-Temperature measurement files, use the analog timing measurement temperature DS18B20
DAC5616DRIVER
- DA芯片DAC5616的Crotex m3驱动程序，采用软件模拟时序操作。实测效果很好。-DA chip DAC5616' s Crotex m3 driver, using software simulation timing operation. Measured with good results.
max197_angle_sensor
- 高精度角度传感器（编码器），AD采用美信公司的max197，程序没有采用总线方式写，而是用IO模拟时序，实测可用-High-precision angle sensor (encoder), AD uses Maxim' s max197, the program does not use the bus way to write, but with the IO timing simulation, the measured a
bsp_RX8025
- RS-8025 驱动程序 IIC模拟时序，STM32F单片机-RS-8025 drivers for IIC simulation timing, STM32F microcontroller
avr-twi
- avr单片机的TWI模块，它的应用比在51单片机中的模拟时序要方便简单。-Avr SCM TWI module, and the application of it than in 51 SCM of the analog timing to the convenience simple.
sccb
- PIC16F877A SCCB通信程序源代码，利用IO口模拟时序-PIC16F877A SCCB communication program source code, the use of analog IO timing
LCD_IO
- 智能小车上使用的摄像头LCD液晶显示图像（使用IO口模拟时序）-Smart small car camera LCD LCD image (using analog IO timing)
DS1302
- 在ABOV单片机上实现DS1302模拟时序的通信。-On in ABOV MCU to achieve the DS1302 analog timing of communication.
ad5791-stm32
- stm32驱动20bit的dac ad5791的程序，模拟时序实现-stm32 driver the 20bit dac ad5791 program, simulation timing to achieve
ADC122_1
- ADC122的SPI模拟时序，用430单片机，IAR软件编写，按照ADC122的时序模拟的采样函数-The ADC122 the SPI analog timing
iic
- 单片机模拟时序，i2c通讯是没有专门端口的福音啊 -MCU I2C communication necessary procedures
Stm32-tlv5616
- tlv5616的实现，用stm32实现。采用模拟时序的方式-The TLV5616 the implementation。Stm32 achieve。Analog timing
RotaryEncoder
- 25位绝对值编码器SSI模拟读取数值,y数值读取正确，采用软件模拟时序-25 SSI absolute encoder analog read values, y values read correctly, the use of software simulation timing
EEPROM
- 完全模拟时序的EEPROM读写程序，各种型号单片机均可使用，缺点操作速度慢，对初学者看懂时序帮助较大。-Fully simulate the timing of EEPROM program, various models of the microcontroller can be used, the disadvantage is slow operation, greater help for beginners to unders
EEPROM2
- 完全模拟时序的多字节存储通信,初学者看后很容易上手,比较直观-Multi-byte storage communication full timing simulation, after beginners very easy to use, more intuitive
led
- 定时器控制LED灯由单片机内部定时器1，按方式1工作，即作为16位定时器使用每0.05秒钟T1溢出中断一次。P1口的P1.0-P1.7分别接八个发光二极管。编写程序模拟时序控制装置。开机后第一秒钟L1，L3亮，第二秒钟L2，L4亮，第三秒钟L5，L7亮，第四秒钟L6，L8亮，第五秒钟L1，L3，L5，L7亮，第六秒钟L2，L4，L6，L8亮，第七秒钟八个LED灯全亮，第八秒钟全灭，以后又从头开始，L1，L3亮，然后L2，L4亮……一直循
AD7606PFSM
- AD7606利用状态机进行模拟时序控制采样。-AD7606 using the state machine to simulate timing control samples.
LCD
- 嵌入式k60的液晶显示（IO模拟时序），测试程序-The LCD embedded k60 (IO analog timing), the test program