搜索资源列表
51单片机超声波测距程序
- 51单片机超声波测距程序1、在打开资料后,请先看相关资料! 2、检查资料是否齐全。 3、如果有问题请及时与我们联系! 4、欢迎与我们交流,并提宝贵意见!(51 singlechip ultrasonic ranging program 1, after opening information, please look at the relevant information! 2, check whether the inform
红外遥控超声波测距
- 该源码是智能小车红外遥控循迹的源码,使用了超声波进行测距避障,开发环境为KEIL,处理器为STM32F103(The source is a smart car tracking infrared remote control the source code, the use of ultrasonic ranging obstacle avoidance, development environment for KEIL, STM32
超声波测距(数码管显示)
- 利用超声波模块测量距离并显示在四段数码管上(Use ultrasonic module to measure distance and display on four section digital tube)
超声波
- stm32f103zet6芯片驱动超声波模块测距(Stm32f103zet6 chip drive ultrasonic module ranging)
超声波传感器实验
- stm32 超声波 传感器实验 实现源码(STM32 ultrasonic sensor experiment)
stm32-超声波避障
- 简单的超声波避障,基于stm32,亲测可用(Simple ultrasonic obstacle avoidance)
超声波测距
- 利用超声波模块,通过STM8实现距离的测量,病痛TM1638显示。(The use of ultrasonic modules, through the STM8 to achieve distance measurement, pain TM1638 display.)
超声波测距
- 超声波模块,可以精确的显示出距离,LCD屏幕显示,里面有51,和ARM的程序。等审核人员审核完成(Ultrasonic module, can accurately display the distance, LCD screen display, there are 51, and ARM program. Audit personnel audit completed)
超声波测距1602LCD显示
- 超声波测距1602LCD显示(Ultrasonic ranging 1602LCD display)
8.超声波测距_定时器
- 基于stc15f2k60s2的超声波测距程序,使用定时器。用数码管显示测出的距离。(Stc15f2k60s2 based ultrasonic ranging program, the use of timers. Display the distance measured with digital tube.)
超声波测距
- 利用89c51实现超声波测试距离,并且用LCD1602显示对应的距离。(Ultrasonic testing distance is realized by 89C51, and the corresponding distance is displayed by LCD1602.)
7.超声波测距_PCA
- 基于stc15f2k60s2的超声波程序,使用sr-04经典超声波模块。使用的是stc15的pca中输入捕获功能,实现对超声波的距离的测量,使用数码管显示程序。(Based on stc15f2k60s2 ultrasonic program, using sr-04 classic ultrasonic module. The use of stc15 PCA input capture function, the realizati
超声波加红外测距传感器监控
- 在labview使用超声波传感器和红外传感器进行距离的监控,本程序监控了5个超声波传感器。(In the use of LabVIEW ultrasonic sensors and infrared sensors for distance monitoring, this program monitors 5 ultrasonic sensors.)
STM32超声波测距
- STM32F103C 超声波测距程序,径过测试 可使用(STM32F103C ultrasonic ranging program, diameter pass test can be used)
三路超声波
- 使用STC15单片机捕获三路超声波来测算距离,并且显示到IIC接口的OLED屏幕上面(Three channel ultrasonic ranging is captured)
超声波测距资料
- 超声波测距,根据超声波指向性强,能量消耗慢,在介质中传播距离远的特点,利用超生波传感器对前方物体进行感应,经过单片机中的程序对超声波传感器发射和接收的超声波信号进行分析和计算处理,最后将处理结果在LCD1602上显示。(Ultrasonic ranging, according to the strong point of ultrasonic energy consumption is slow, the propagation ch
超声波测距(LCD1602显示)
- 51单片机超声波测距程序,采用LCD1602液晶显示屏显示(51 SCM ultrasonic ranging program, using LCD1602 LCD display)
13.0 超声波测距(数码管显示)
- 超声波测距 Trig ------- P2^1; Echo ------- P2^0; VCC -------- +5v GND -------- GND 请在上电之前,检查好接线是否正确。(ultrasonic ranging Trig ------- P2^1; Echo ------- P2^0; VCC -------- +5v GND -------- GND)
超声波测距
- 用单片机来实现超声波进行测距,其中程序用C语言实现,仅供参考(Using MCU to achieve ultrasonic ranging, in which the program is implemented in C language, for reference only)
超声波 模块(10次)
- 利用STM32ZET6和超声波模块,通过十次测量求平均值,实现超声波测距的功能(Using STM32ZET6 and ultrasonic module, the average value is obtained by ten measurements, and the function of ultrasonic ranging is realized)