搜索资源列表
5110
- 5110驱动文件，配合头文件显示5110液晶数据(5110 drive files, with the header file to display 5110 LCD data)
frequence test Proteus simulation(C51)
- 通过proteus 仿真 利用51编程实现 频率测量 附有电路仿真图以及所用程序(Through the Proteus simulation, using 51 programming frequency measurement, with circuit simulation diagram and the procedures used)
仿真文件及原代码
- 用51单片机控制电机正反转，开始或停止以及速度等(51 SCM control motor positive and negative, as well as speed)
uCOS-IIFORC51
- 移植uCOS-II到C51单片机，很实用的一个工程(Transplant uCOS-II to C51 microcontroller, a very practical project)
三轴计步器
- 一个基于51单片机和AHXL345传感器模块的的计步器程序，能显示步数，总步数，热量消耗。(Based on a 51 MCU and AHXL345 sensor pedometer module procedures, can display the number of steps, the total number of steps, calorie consumption.)
KeilC51V9.00
- KEIL的C51破解版，keil环境下编辑C51(KEIL C51 crack version, edit the C51 in keil environment)
0625、8路抢答器
- 用汇编语言和c语言实现8路抢答器功能，包含仿真图和源程序，以上内容仅供学习交流使用，若用于商业用途作者将追究责任。(Using assembly language and C language to achieve 8 way responder function, including simulation and source code, the above content is only for learning, exchange
智能计算器
- 智能计算器 基于51单片机 可以实现小范围数据的计算。(Intelligent calculator based on 51 single-chip microcomputer, you can achieve a small range of data calculation.)
两只老虎
- 用51系列板子实现蜂鸣器唱歌，唱两只老虎(Buzzer singing with 51 boards)
baicidengkongzhi
- 51单片机程序，LED等控制C程序，keil下编译，protuse仿真，适合初学者(51 Singlechip procedures, LED and other control C procedures, Keil compiler, protuse simulation, suitable for beginners)
chuankutongxun
- 51单片机程序，串口控制C程序可与PC交互，keil下编译，protuse仿真，适合初学者(51 Singlechip procedures, serial control C procedures, and PC interactive, Keil compiler, protuse simulation, suitable for beginners)
（在两个中）识别最大模拟输入通道
- （在两个中）识别最大模拟输入通道 利用0809采集两路模拟电压，将电压值最大的通道号显示在LED显示器上。（硬件电路参见AD_CH2_1.DSN）。((in two) identifying the maximum analog input channel Using 0809 to collect two analog voltage, the voltage value of the largest channel number
PWM波发生器
- 在硬件电路PWM.DSN中实现P1.7输出PWM波。周期T=100ms，初始占空比（T1/T）为50%，按键KEY1每次增加占空比10%（直到90%），KEY2每次减小占空比10%（直到10%）。(In hardware circuit PWM.DSN, P1.7 output PWM wave is realized. The cycle T=100ms, the initial duty cycle (T1/T) is 50%, t
3X3键盘扫描
- 利用8155的PB、PC口实现3X3键盘扫描（硬件电路参见3X3KEY_8155.DSN）。当1~8号键独立按下时，连接在PA口对应的LEDx点亮（即1号键按下时LDE1亮，2号键按下时LDE2亮），当9号键按下时，所有LED点亮，当没有键按下时，所有LED熄灭。(3X3 keyboard scanning with 8155 PB and PC ports (hardware circuit, see 3X3KEY_8155.DSN)
50赫兹同步锯齿波发生器
- 利用0832同步输出两个频率为50赫兹的锯齿波（硬件电路参见DA_BUF2_1.DSN）。(Using 0832 simultaneous outputs, two sawtooth waves with frequencies of 50 Hz (hardware circuit refer to DA_BUF2_1.DSN) are used.)
编码显示器
- 利用8255扩展并行端口（硬件电路参见CodeDisplay_8255.DSN）。当KEY按下时，利用8255的PC口输入二进制值编码（6位），将该值转换成十进制后显示在2位7段LED显示器上。(Using 8255 to extend parallel ports (see CodeDisplay_8255.DSN for hardware circuits). When the KEY is pressed, the binary
红外避障导盲仪设计程序
- 导盲仪设计源程序，实现检测障碍物报警和照明控制功能。(Guide detector design source code, to detect obstacles, alarm and lighting control function.)
51单片机仿真案例
- 此代码适用于51入门，包含了51单片机的基本的外设，简单易学。(This code applies to the 51 entry, including the 51 microcontroller basic peripherals, easy to learn.)
music
- 51单片机音乐盒，内有天空之城等音乐，蜂鸣器播放，带有上一曲，下一曲，暂停等按键。(51 single - chip computer music box, the city of sky and other music, the buzzer playing, with the previous song, the next song, pause, and so on.)
译码器动态显示
- 动态译码管的显示程序，原创，适用于学习。(Dynamic decoding tube display program, original, applicable to learning.)