资源列表

« 1 2 ... .81 .82 .83 .84 .85 986.87 .88 .89 .90 .91 ... 1228 »

[串口编程FX-Communication

说明:VB上位机与三菱PLC通信,M值置位复位,D值读写。-FX Communication
<panchaoren> 在 2025-06-11 上传 | 大小:33kb | 下载:0

[串口编程VB

说明:VB串口调试助手源代码,很好,很强大。适合初学者使用!-VB serial debugging aids source code, very good, very powerful. Suitable for beginners!
<苏规避> 在 2025-06-11 上传 | 大小:113kb | 下载:1

[串口编程ASerialPortset

说明:包含8个不同串口通讯示例,调试工具源代码,同步异步串口类,及多线程通讯,很多可以直接应用到开发中。-Includes eight different serial communication example, source code, debugging tools synchronous asynchronous serial interface, and multi-threaded communications, many can be directly applied to the de
<wanglizhen> 在 2025-06-11 上传 | 大小:21.08mb | 下载:0

[串口编程serial_linux

说明:This a simple code using COM port in Linux. The host sends a packet of 6 bytes (including CRC) through serial port and waits for the responding packet. If CRC is correct, the packet is parsed to get some useful data. Test code and Makefile is include
<Kang Yong Rim> 在 2025-06-11 上传 | 大小:4kb | 下载:0

[串口编程BH5100

说明:获取bh5100微量元素结果,delphi开发例子。成熟代码-Get bh5100 trace results
<程永平> 在 2025-06-11 上传 | 大小:744kb | 下载:0

[串口编程CRC16

说明:16位CRC校验查找表法,网上比较普遍的是8位表,该程序中有罕见的4位表,亲,千万不要错过哦,赶快下载吧!-16-bit CRC lookup table method, the Internet more generally eight tables, this program has the rare four tables, pro, do not miss it, download it!
<谭平> 在 2025-06-11 上传 | 大小:1kb | 下载:0

[串口编程SerialPortComm

说明:此程序是一个串口调试助手。可以实现16进制发送接收。用MFC编写。-This program is a serial debugging assistants can realize hexadecimal to send and receive written in MFC
<李冉冉> 在 2025-06-11 上传 | 大小:7.18mb | 下载:0

[串口编程Beierguanbiduankou

说明:贝尔7353批量或者单个关闭端口,查看端口状态,很实用-Bell 7353 batch or single shut down the port, check the port status, it is practical
<安继业> 在 2025-06-11 上传 | 大小:1kb | 下载:0

[串口编程SCIFIFOINTtext2

说明:本程序是上位机与DSP通讯,DSP以FIFO的接收中断方式接收上位机的数据,再将数据发回给上位机-This procedure is the communication between PC and DSP, DSP receiver FIFO interrupt to the host computer receives the data, then the data is sent back to the host computer
<mengjing> 在 2025-06-11 上传 | 大小:305kb | 下载:0

[串口编程tcp

说明:主要用于计算机之间的连接通信,运用的是TCP协议-Mainly used for communication between computers connected to, the use of the TCP protocol
<朱祖灿> 在 2025-06-11 上传 | 大小:84kb | 下载:0

[串口编程UART

说明:用verilog编写的UART串口通信程序,经验证误码率为0,系统由ARM控制FPGA的串口进行通信;-Written in verilog UART serial communication procedures, proven error rate is 0, the system controlled by ARM FPGA serial communication
<lejing> 在 2025-06-11 上传 | 大小:3kb | 下载:0

[串口编程PCserial-communication

说明:设计一个与PC串口通信的实验系统,当在PC机上输入十进制数时,可在实验板上显示相应的十六进制数字,而在实验板上按下独立按键A时,在PC机上也可以显示其对应的管脚数56。-Design an experiment with the PC serial communication system, when the PC input decimal number, you can experiment on-board display the corresponding hexadecimal num
<张三> 在 2025-06-11 上传 | 大小:145kb | 下载:0
« 1 2 ... .81 .82 .83 .84 .85 986.87 .88 .89 .90 .91 ... 1228 »

源码中国 www.ymcn.org