资源列表
[单片机(51,AVR,MSP430等)] MMC11111111111
说明:MMC 卡的资料,的利与大家读写MMC卡,扩展更大的存储器-MMC card information, and we facilitate the MMC card reader, a greater expansion of memory!<余震难> 在 2025-12-03 上传 | 大小:10kb | 下载:0
[单片机(51,AVR,MSP430等)] aduc70xx_adc
说明:USB是主从总线,上位机不读,下位机无法上传。所以当上位机调用ReadData时,下位机才能上传数据,当然,下位机应该准备好数据,如果没有准备好,上位机程序会一直等待下去,像停机一样。-USB is the main from the bus, not to be PC, the next crew unable to upload. So when PC calling ReadData, where crew can upload data, of course, the next crew<立志军> 在 2025-12-03 上传 | 大小:10kb | 下载:0
[单片机(51,AVR,MSP430等)] weibo
说明:微波治疗仪的源程序,现在已经开始生产。只可以参考,因为有版权。-microwave apparatus of the source has now started production. Only a reference because of copyright.<雪肤> 在 2025-12-03 上传 | 大小:10kb | 下载:0
[单片机(51,AVR,MSP430等)] avrfuweifanli
说明:avr-atmega复位检测与看门狗范例-avr- SPARC reset detection and watchdog example<dfggdfh> 在 2025-12-03 上传 | 大小:10kb | 下载:0
[单片机(51,AVR,MSP430等)] hellodanpianji
说明:这是个单片机的HELLOWORLD小程序初次上传请多关照-This is a small MCU HELLOWORLD procedures upload news conference for the first time<dark> 在 2025-12-03 上传 | 大小:10kb | 下载:0
[单片机(51,AVR,MSP430等)] PIC_CCS_C_eeprom
说明:PIC单片机的eeprom使用ccs源码-PIC ccs of EEPROM use FOSS<三强> 在 2025-12-03 上传 | 大小:10kb | 下载:0
[单片机(51,AVR,MSP430等)] asm_wave
说明:一些常用的波形生成程序,汇编写的,经过测试,放心使用-some common waveform generation, assembler written, tested and assured use<bluewater523> 在 2025-12-03 上传 | 大小:10kb | 下载:0
[单片机(51,AVR,MSP430等)] 192168lcd
说明:192*64 128*64LCD代码程序-192* 64128* Embedded code procedures<ccc> 在 2025-12-03 上传 | 大小:10kb | 下载:0
[单片机(51,AVR,MSP430等)] ycx
说明:文件中包括电子琴、步进电机控制、电子钟等实用程序控制,已经通过了编译,适当设计编译环境、端口等相信会对该方面的朋友有帮助。-document include organ, stepper motor control, electronic bell practical programmed through a compiler, appropriate Design Compiler environment, ports, etc. I believe that the friends help<程承> 在 2025-12-03 上传 | 大小:10kb | 下载:0
[单片机(51,AVR,MSP430等)] I2C_bit_C51
说明:模拟I2C总线通信协议,位方式,C51编程,很好用的喔!-simulation I2C bus communication protocols, bit, C51 programming, the good!<郑> 在 2025-12-03 上传 | 大小:10kb | 下载:0
[单片机(51,AVR,MSP430等)] single-key-adjust-clock
说明:显示数据在70H-75H单元内,用六位LED共阳数码管显示,P1口输出段码数据,P3口作 扫描控制,每个LED数码管亮1MS时间再逐位循环。 定时器T0、T1溢出周期为50MS,T0为秒计数用, T1为调整时闪烁用, P3.7为调整按钮,P1口 为字符输出口,采用共阳显示管。 -display the data in the 70H-er cell, with a total of six Yang digital LED Display, P1 mouth of<fengming> 在 2025-12-03 上传 | 大小:10kb | 下载:0