资源列表

« 1 2 ... .23 .24 .25 .26 .27 9828.29 .30 .31 .32 .33 ... 15240 »

[单片机(51,AVR,MSP430等)STC12C5204AD_DSP2812_handle_program

说明:基于STC12C5204AD的机器人手柄程序设计,通过该单片机的手柄程序,与DSP2812微处理器通信实现手柄控制机器人运动。-Robot based STC12C5204AD handle programming, through the SCM handle procedures, and the DSP2812 Communication microprocessor to control the robot motion controller.
<wengchaowc> 在 2025-06-30 上传 | 大小:18kb | 下载:0

[单片机(51,AVR,MSP430等)Blinky

说明:LPc1768单片机的流水灯使用例程,具有很好的参考价值-LPc1768 single chip using routine light water, a good reference value
<电子迷> 在 2025-06-30 上传 | 大小:18kb | 下载:0

[单片机(51,AVR,MSP430等)cw

说明:一个简单的超声波和红外结合蔽障的程序,请参考!-A simple combination of ultrasound and infrared barriers shield the procedure, please refer to!
<vieri3221> 在 2025-06-30 上传 | 大小:18kb | 下载:0

[单片机(51,AVR,MSP430等)51_1602LCD

说明:51单片机1602LCD驱动和测试程序,keil环境-51 SCM 1602LCD driver and test programs, keil environment
<yxq> 在 2025-06-30 上传 | 大小:18kb | 下载:0

[单片机(51,AVR,MSP430等)yjzc

说明:基于pic16f877a的串行通信 输出为16进制,输入为10进制-Serial communication output based on pic16f877a 16 hex, 10 decimal input
<zxy > 在 2025-06-30 上传 | 大小:18kb | 下载:0

[单片机(51,AVR,MSP430等)KANMENGOU

说明:本程序是实现51系列单片机看门狗设定的程序-The program is set to achieve 51 MCU watchdog
<江旭> 在 2025-06-30 上传 | 大小:18kb | 下载:0

[单片机(51,AVR,MSP430等)RS-485

说明:此代码是基于RS-485的多机通讯,清晰的代码使你一目了然。-This code is based on the RS-485 Multi-machine communication, clear the code to make you a glance.
<闫伟> 在 2025-06-30 上传 | 大小:18kb | 下载:0

[单片机(51,AVR,MSP430等)dianti

说明:STC51点阵模拟电梯上下行程序,通过按键控制-STC51 lattice simulation program up and down the elevator, through the control buttons
<沙居峰> 在 2025-06-30 上传 | 大小:18kb | 下载:0

[单片机(51,AVR,MSP430等)mima

说明:给于单片机的密码锁的源程序,很详细,简单一点-To lock in the microcontroller of the source, very detailed, it simply
<陈龙成> 在 2025-06-30 上传 | 大小:18kb | 下载:0

[单片机(51,AVR,MSP430等)1602

说明:KS0070(44780) 16x2 字符液晶屏驱动演示程序总线方式,AT89C51的晶振频率为12MHz-KS0070 (44780) 16x2 character LCD screen, the bus driver demo mode, AT89C51 crystal frequency is 12MHz
<hexiaobin> 在 2025-06-30 上传 | 大小:18kb | 下载:0

[单片机(51,AVR,MSP430等)GGJCX

说明:此为单片机控制的全自动轴承内圈和外圈精密割管机程序-This is a microprocessor controlled automatic bearing inner and outer rings of the machine precision cutting process
<韩华> 在 2025-06-30 上传 | 大小:18kb | 下载:0

[单片机(51,AVR,MSP430等)46590_144330725601990_142855732416156_181293_4485

说明:CV SD ZS SSS AAREN LEWES EWER R OVERWROTE ERRATUM
<mahmoud> 在 2025-06-30 上传 | 大小:18kb | 下载:0
« 1 2 ... .23 .24 .25 .26 .27 9828.29 .30 .31 .32 .33 ... 15240 »

源码中国 www.ymcn.org