资源列表
[其他嵌入式/单片机内容] classroom-solutions
说明:C FILE REGARDING SMART CLASSROOM CODE FOR ATMEGA32A.<rdx> 在 2024-06-18 上传 | 大小:1024 | 下载:0
[其他嵌入式/单片机内容] youxianyuan
说明:有限元方法matlab程序求节点位移向量-FEM node displacement vector matlab program seeking<马童鞋> 在 2024-06-18 上传 | 大小:1024 | 下载:0
[其他嵌入式/单片机内容] ht1622driveLCD
说明:用2个ht1622驱动LCD,可以直接用的测试程序。-Use two ht1622 drive LCD, can directly use the test program.thank you<吴勇> 在 2024-06-18 上传 | 大小:1024 | 下载:0
[其他嵌入式/单片机内容] nodemcu-web
说明:nodemcu简单网页代理,使网页穿透内网,实现远远程物联网基础控制-Nodemcu simple web proxy, make a web page through the network, achieve far remote Internet based control<王文> 在 2024-06-18 上传 | 大小:1024 | 下载:0
[其他嵌入式/单片机内容] Moto
说明:关于stm32f10x 的 pwm 源代码设计, 基于四轴飞行器的电机设计方法-part function about stm32f10x PWM<fuxiao> 在 2024-06-18 上传 | 大小:1024 | 下载:0
[其他嵌入式/单片机内容] ADC_of_MSP430F249
说明:A single sample is made on A10 with reference to internal 1.5V Vref. Software sets ADC12SC to start sample and conversion - ADC12SC automatically cleared at EOC. ADC12 internal oscillator times sample and conversio<sattarhastam> 在 2024-06-18 上传 | 大小:1024 | 下载:0
[其他嵌入式/单片机内容] TimerA_of_MSPF249
说明:Toggle P1.0 using software and the TA_0 ISR. Timer_A is configured for up mode, thus the timer overflows when TAR counts to CCR0. In this example, CCR0 is loaded with 1000-1. ACLK = TACLK = INCLK = 32768Hz, MCLK =<sattarhastam> 在 2024-06-18 上传 | 大小:1024 | 下载:0
[其他嵌入式/单片机内容] I2C_of_MSP430F249
说明:This demo connects two MSP430 s via the I2C bus. The master reads 5 bytes the slave. This is the MASTER CODE. The data the slave transmitter begins at 0 and increments with each transfer. The USCI_B0 RX interrupt i<sattarhastam> 在 2024-06-18 上传 | 大小:1024 | 下载:0
[其他嵌入式/单片机内容] SPI_of_MSP430F249
说明: SPI master talks to SPI slave using 3-wire mode. Incrementing data is sent by the master starting at 0x01. Received data is expected to be same as the previous transmission TXData = RXData-1. USCI RX ISR is use<sattarhastam> 在 2024-06-18 上传 | 大小:1024 | 下载:0
[其他嵌入式/单片机内容] UART_of_MSP430F249
说明: Echo a received character, RX ISR used. Normal mode is LPM0. USCI_A0 RX interrupt triggers TX Echo. Baud rate divider with 1MHz = 1MHz/19200 = ~52.1 ACLK = n/a, MCLK = SMCLK = CALxxx_1MHZ = 1MHz<sattarhastam> 在 2024-06-18 上传 | 大小:1024 | 下载:0
[其他嵌入式/单片机内容] FLASH_WRITE_of_MSP430
说明: This program first erases flash seg C, then it increments all values in seg C, then it erases seg D, then copies seg C to seg D. Seg C @ 1040h Seg D @ 1000h The EEI bit is set for the Flash Erase Cycles. This does<sattarhastam> 在 2024-06-18 上传 | 大小:1024 | 下载:0
[其他嵌入式/单片机内容] zephyr_sensor
说明:基于Zephyr v1.7.0开发的MPU6050 sensor读取程序,MPU6050的驱动位置zephyr目录zephyr-v1.7.0/drivers/sensor/mpu6050-MPU6050 sensor application base on Zephyr v1.7.0, the MPU6050 driver is under zephyr-v1.7.0/drivers/sensor/mpu6050<韦伯> 在 2024-06-18 上传 | 大小:1024 | 下载:0