资源列表
[LabView] Cross-correlation
说明:基于labview8.6的FFT法测量低信噪比条件下两路方波信号的相位差,经测试,幅值测量精度和相位测量精度都很高-Based labview8.6 FFT method to measure the phase difference between the two square wave signals in low signal-to-noise ratio conditions, test, amplitude measurement accuracy and phase measurem<罗知亮> 在 2025-08-02 上传 | 大小:51kb | 下载:0
[LabView] RS232HELPERLabview2012
说明:labview 2012 串口通信助手 -labview 2012 serial communication assistant<张利民> 在 2025-08-02 上传 | 大小:51kb | 下载:0
[LabView] TreeExample
说明:labview树形控件,实现节点的添加和删除-tree control can add and remove element<王均> 在 2025-08-02 上传 | 大小:51kb | 下载:0
[LabView] deal_with_error.tar
说明:labview 开发教程 错误处理有关方面的一些示例- development tutorial labview error handling some examples of relevant<nan> 在 2025-08-02 上传 | 大小:51kb | 下载:0
[LabView] successWaveform
说明:电压尖峰发生器上位机labview语言代码(包含与飞思卡尔单片机的232通讯,逻辑输出控制,触控屏通讯)-Voltage spike generator PC LabVIEW language code<王明亮> 在 2025-08-02 上传 | 大小:51kb | 下载:0
[LabView] Signal power spectrum based on FFT
说明:通过labview 对信号进行分析,主要包括基于FFT求信号功率谱(The signal is analyzed by LabVIEW, mainly including the signal power spectrum based on FFT)<yingzhiwuying > 在 2025-08-02 上传 | 大小:50kb | 下载:0
[LabView] 导航坐标系转换labview
说明:主要包含经纬高信息、北天东坐标系、地心坐标系之间的坐标转换,用labview实现的。(It mainly includes the coordinate transformation between the latitude and longitude information, the North East coordinate system and the geocentric coordinate system. It is realized by LabVIEW)<hitwwf> 在 2025-08-02 上传 | 大小:50kb | 下载:0
[LabView] 抓取第三方界面文字程序
说明:能够获取第三方界面句柄及文字信息,进行相关操作。(Get third party interface text)<purewhite> 在 2025-08-02 上传 | 大小:50kb | 下载:2
[LabView] 液位控制例程
说明:labview仿真,水箱液位控制,很好的一个例子控制系统的计算机仿真是一门涉及理论、计算数学与计算机技术的综合性学 科。控制系统的计算机仿真以控制系统的模型为基础,采用数学模型代替实际的 控制系统的控制系统,以计算机为工具,对控制系统进行实验和研究的一种方法。(Lab VIEW simulation, water tank level control, a good example computer simulation of control system is a comprehensiv<撒大大s> 在 2025-08-02 上传 | 大小:50kb | 下载:0
[LabView] 拉力传感器电机控制
说明:数据采集卡采集拉力值,与预先设定的拉力值进行比较,然后PID运算,控制相应的PWM占空比输出,最终控制电机的速度(The data acquisition card collects the pull value and compares it with the pre-set pull value. Then the PID arithmetic is used to control the output of the corresponding PWM duty cycle, and fin<羽生结弦> 在 2025-08-02 上传 | 大小:50kb | 下载:0