资源列表
[软件工程] 883679-PulseAutobuyer1.0.4..3voRocks07
说明:pulseauotobuyer used in neo<喬至豪> 在 2025-07-05 上传 | 大小:214kb | 下载:0
[软件工程] ModernC++Design
说明:一本关于VC++的经典书,详细讲解了C++的设计模式,值得大家一看。-On a VC++ Classic book, detailed account of C++ The design mode, what is worth a look.<xiaochunlei> 在 2025-07-05 上传 | 大小:1.16mb | 下载:0
[软件工程] SoftEngineer
说明:储蓄存款子模块基本分析,对其进行了详细的分析,包括需求分析、概要设计、详细设计-Savings deposits module basic analysis, carried out a detailed analysis, including needs analysis, outline design, detailed design<sky> 在 2025-07-05 上传 | 大小:217kb | 下载:0
[软件工程] P4_PPC_SDRAM_Reference_Design
说明:SDRAM 参考设计:主要包括The following figure shows a high-level block diagram for this reference design followed by a brief descr iption of each sub-section. The design consists of: · PowerPC processor · PLB-OPB bridge · BlockRAM Memory Controller ·<庞志勇> 在 2025-07-05 上传 | 大小:33kb | 下载:0
[软件工程] rup
说明:做软件工程必备手册,就相当于做事情的时候好的计划书,当你为你的程序设计好流程的时候,那么你的程序已经完成了一半!-Required to do software engineering manuals, on the equivalent of doing anything good plan, when you for your good program design procedures, then your procedures have been completed in half!<jobs> 在 2025-07-05 上传 | 大小:498kb | 下载:0
[文档资料] hangbianji
说明:具体实现以下4条基本编辑命令: (1) 行插入。格式:i《行号》《回车》《文本》。《回车》 将《文本》插入活区中第《行号》行之后。 (2) 行删除。格式:d《行号1》[《空格》《行号2》]《回车》 删除活区中第《行号1》行(到第《行号2》行)。例如:“d10”和“和d10 14”。 (3)活区切换。格式:n《回车》 将活区写如输出文件。并从输入文件中读入下一段,作为新的活区。 (4)活区显示。格式:p《回车》 各条命令中的行号均须在活区中各行行号范围之内,只<andy> 在 2025-07-05 上传 | 大小:2kb | 下载:0
[软件工程] 100MHz-visual-oscilloscope
说明:从自主研发的角度,提出了基于虚拟仪器的数字示波器的一种新的设计方法,该方法对数据采集卡硬件设计和配套软件的开发进行了研究。采用PCI接口,用DMA方式传输据,使得采样频率可达100MHz,用户可通过软面 板设置采样参数,采集的数据先送到系统内存,再直接以波形形式显示到软面板上,或者以数据文件格式存到Pc机硬盘。该虚拟示波器已成功运用于弱电信号的采集。-Independent research and development from the perspective of virtual in<田宇> 在 2025-07-05 上传 | 大小:171kb | 下载:0