搜索资源列表
DA
- 采用DAC0832实现数模转换,分别将一组数据转换为锯齿波,三角波,正弦波,在一种波形输出时,按Q键转为输出下一种波形。-used to achieve several DAC0832 mode conversion, respectively, to a group of data conversion for the ramp, triangle wave, sine wave, in a waveform output, acco
正弦波发生器汇编源程序
- 我第一次上传,水平有限,望大家多指教,这里先发5个,以后会陆续上传-I first uploads limited, and we hope more exhibitions here starting five, the future will continue to upload
sinewavedataV0.1
- 正弦波数据产生程序,升级版本, 更方便,不必必源程序,直接输入所要产生的数据个数!-sine wave data generation procedures, upgrade versions, more convenient, and certainly not the source. directly import data to the number!
DAconversion
- 这是一个由51单片机控制的数模转换器(DAC0832),可已输出正弦波,方波,阶梯波,三角波等模拟信号-This is a 51 MCU control of the Digital to Analog (DAC0832). sine wave output can be had, square, ladder wave, triangular wave signal simulation
C8051_DA_test
- 摘 要: 本文件是C8051单片机DA测试实验程序;使用外部22.1184MHz晶振. 功能:定义 A ~ F 为功能键。 按"A" 键,输出250HZ的方波,按"B" 键,输出250HZ的正弦波形,按"C" 键,输出250HZ的三角波, 按"D" 键,输出250HZ的锯齿波。用示波器在J6(DAC0)观测结果,使用串口观测按键信息。-Abstract : This document is C8051 MCU DA lab
DA_lyang
- 实现正弦波、三角波、锯齿波三种波形输.用3个按键实现不同波形的输出.适用于初学者作为入门的程序.-achieve sine, triangle wave, sawtooth waveform three losers. used three different keys to achieve the output waveform. apply to beginners as induction procedures.
musicplay51mcu
- 单片机用T1中断在IO口P1.0输出乐曲(在P1.0口与VCC间接一喇叭即可听到) // // 1.由于输出的是方波,比较难听:-)你也可以将波形细分用DA输出正弦波 // // 2.由于T1频繁中断,任何其他中断发生都会是乐曲打顿,只适合试验 // // 3.优化音符编码:一个字节中包含节拍、音符、升降调,可区分数据和命令-T1 chip Computer IO interruption in output P1.0 mo
SIN
- 利用单片机以及DA0832产生正弦波的C51源程序-As well as the use of single-chip generated sine wave DA0832 source of C51
sin
- DAC0800产生幅度可调正弦波的程序,调试通过了哦-Generated sine wave amplitude adjustable DAC0800 procedures, debugging through the oh
DA
- DA代码 经测试通过的c8051f020 DA代码 内有锯齿波, 正弦波, 三角波等产生的代码... -DA code has been tested and adopted c8051f020 DA code, there are sawtooth, sine wave, triangular wave generated by code such as ...
da0832
- 利用89s52外加da0832实现正弦波的产生,已经调试通过-89s52 plus da0832 realize the use of sine wave generation, have been debugging through
xinhaofashengqi
- 利用高速da通过查表法进行正弦波,方波,三角波产生的stc89c51程序和波形码表生成的c程序-err
dac0832driver
- 基于DAC0832的多功能波形发生器,可以输出正弦波,方波,锯齿波,三角波-DAC0832-based multifunction waveform generator can output sine wave, square wave, sawtooth wave, triangle wave
C51
- 单片机P1口与4个按键连接,用于信号幅度和频率调节操作键。单片机P0、P2.7、P3.6(-WR)与DA0832、2个741(运放)连接构成波形信号输出电路。 编程使波形信号输出电路输出正弦波信号,并且可通过操作键调节信号的幅度和频率。幅度和频率调节级别从0~10,共11个等级。 -Singlechip P1 I connect with the four buttons for the signal amplitude and
DA
- TMS320LF2407键盘与DA转换综合控制源码 键盘0,1,2,3分别使得DA转换产生方波,三角波,正弦波,锯齿波。-TMS320LF2407 keyboard with integrated control DA converters 0,1,2,3-source keyboard makes DA conversion separately generated square wave, triangle wave, sine
da
- 通过DA转换查表实现正弦波输出,无法调节周期-DA conversion look-up table to achieve through the sine wave output, can not adjust the cycle
dac0832
- DAC0832 DA转换 三角波 正弦波 以及锯齿波 的源程序-DAC0832 DA conversion triangle-wave sine wave, as well as the source sawtooth
DA
- 波形发生器啊 可以产生方波,锯齿波 三角波 正弦波-Ah waveform generator can produce square wave, sawtooth wave sine triangle
DA
- 利用DAC0832的单片机输出正弦波信号,高精度,频率、幅度可调 -DAC0832 microcontroller using the output sine wave signal, high precision, frequency, amplitude adjustable
DA正弦波三角波输出测试51
- 通过改变单片机的DA输出电压,可以得到各种各样的电压波形输出,下面介绍产生正弦波形需送DA的数据是如何计算的。 首先既然是正弦波,那么就要确定要输出一个周期正弦波的采样点数point,即由多少点组成了一周期的正弦波,还要知道单片机输出DA的数字值maxnum是多少,比如 8位DA,maxnum=256。10位DA,maxnum=1024。 知道以上两个值后,就开始计算需要得到的正弦波DA数据了,我设置一