搜索资源列表
CO2 Laser Tube Kit
- <35 Watt Flowing Gas CO2 Laser Tube Kit>，自制二氧化碳激光发生器。-lt; 35 Watt Flowing Gas CO2 Laser Tube Kitgt; Made of carbon dioxide laser generator.
Tube
- 一本电子管的老教科书，讲述电子管的原理、制作。-a tube of old textbooks, on the principle of tube production.
The.symbol.points.demonstrated.on.the.digital.tube
- 本代码是关于符点数在数码管上显示的，请注意查收，测试。-code on the website points in the digital displayed on the tube, please note please find test.
Digital tube display program design
- Digital tube display program design Digital tube display program design Digital tube display program design Digital tube display program design Digital tube display program design
CO2 Laser Tube Kit
- <35 Watt Flowing Gas CO2 Laser Tube Kit>，自制二氧化碳激光发生器。-lt; 35 Watt Flowing Gas CO2 Laser Tube Kitgt; Made of carbon dioxide laser generator.
Tube
- 一本电子管的老教科书，讲述电子管的原理、制作。-a tube of old textbooks, on the principle of tube production.
C8051_I2C_E2PROM
- 摘 要： 本文件是C8051单片机I2C总线读写测试程序；将跳线器JP6短接，使用外部22.1184MHz晶振. 功能：定义 0 ~ 9 键为数字键， A ~ F 为功能键。按 A 键后，可按0 ~ 9 数字键， 从零地址开始存储该键值，并送LED数码管上显示该键值。按 C 键停止后，按 B 键， 从零地址开始读取数据值，并送LED数码管上显示。读取速度每秒一次。在按 C 键停止后，可按 A 键重新输入。 -Abstract
The.symbol.points.demonstrated.on.the.digital.tube
- 本代码是关于符点数在数码管上显示的，请注意查收，测试。-code on the website points in the digital displayed on the tube, please note please find test.
show-595
- 我自己编写的74HC595数码管显示程序,一个595驱动两个共阳极数码管-I have written 74HC595 digital tube display program, a total of 595 drive two digital tube anode
LED_display
- LED数码管上显示任意十六进制数字，并且利用中断直接实现扫描-LED digital tube display arbitrary hexadecimal digits, and realize the use of interrupted direct scanning
e_clock
- 单片机是52的，P0口连到四个数码管的七个管脚，其中两个冒号点为最后两个数码管的DOP点，P1.0至P1.3为四个数码管的选通端，低电平有效。程序2较完整，可实现设定时间功能。-Singlechip is 52, P0 port connected to four of the seven-pin digital tube, two of which point to the last two colon tube DOP-point
shixian7duanxianshi
- 51单片机实现7段数码管显示源代码+Sch电路原理图-51 Singlechip realize 7 digital tube display source code+ Sch circuit schematic
13
- 使用Cypress的Cy7C68013A芯片进行设计，控制外部LED数码管的显示。程序包括USB固件程序以及主机程序-The use of Cypress s CY7C68013A chip designed to control the external LED digital tube display. This process includes the USB firmware and the host program
SPI
- LPC2124 SPI接口控制LED数码管显示0-F字符,同时控制4个LED显示对应的十六进制程序，包括PROTEUS仿真电路。-LPC2124 SPI interface to control LED digital tube display 0-F characters, simultaneous control of four LED display the corresponding hexadecimal procedures
MyClock
- 用51单片机实现数字钟 利用数码管、I/O口实现数字钟的计数功能，并显示在数码管上-With 51 single-chip digital clock use of digital control, I/O port to achieve digital clock counting function, and display in the digital tube
74ls164-0TO99
- 74ls164数码管的显示程序，程序完成的功能如下：从0显示到9 -74ls164 digital tube display procedures, procedures for the completion of the function are as follows: from 0 to 9 displayed
digtalLED
- 6位数码管显示程序，通过AT89S/C52,11.0592MHz控制， 显示非常稳定。一个符号位， 5个数据位（3整数，2小数）-6 digital tube display program, through AT89S/C52, 11.0592MHz to control, indicating very stable. A sign bit, 5 data bits (3 integers, 2 decimals)
DS1302
- 单片机控制时钟芯片DS1302，数码管显示程序-Single-chip microcomputer to control the clock chip DS1302, digital tube display program
DISP
- STC单片机数码管测试程序，P4.0控制595时钟，P4.3控制595锁存，高有效， P4.1为LED 数据输入口-STC Single-chip digital tube test procedure, P4.0 control 595 clock, P4.3 control latch 595, high-effective, P4.1 input data for the LED
AVR165-46R47
- 数码管显示的接触式交流稳压器MCU46R47-Digital tube display contact AC voltage stabilizer MCU46R47