搜索资源列表
Panel_new
- 此代码为云台的控制程序，可以控制其水平和俯仰关节的速度和位置。-This code is head of the control program can control the level and pitch speed and location of joints.
CameraControllersrc
- 云台串口控制程序。支持派尔高D、P协议 可以为想学习串口控制的人提供参考-UART SDFSDG A SGDSFGS DFGA SGGAF
Ctrl
- 485通信，通过键盘操作，利用单片机对云台的控制程序-485, through the keyboard, the use of SCM on the head of the control program
VC-camera-control
- 一个设想头控制程序，通过串口控制云台，采用的是派尔高协议-An idea first control program, control PTZ through the serial port, using the Pelco protocol
LDCameraController-src
- 精美的云台控制程序，带Flash加载窗口、支持多线程串口通讯、IOCP、同步异步通信。-Fine PTZ control procedures with the Flash to load the window to support multi-threaded serial communication, the IOCP, synchronous to asynchronous communication.
YunTaiCtrl
- 云台控制程序，里面有几个lib分别实现串口控制 和 云台指令设置 还有一个test程序-two lib one for Com anther for Set then a test exe may be useful to you
PTZ_89C51_D
- 云台镜头控制板的源程序，采用89C51单片机，C语言源代码，实际测试通过。 环境STC51单片机配11.0592晶振，支持协议pelco-d，采用485和RS232均通过测试，2400BPS。地址码按默认1.**是51芯片上的程序可不是电脑PC上的控制程序。测试用电脑上和用监控键盘均可以控制。编译通过Keil_C.-PTZ control panel source 89C51 microcontroller C language sou
codedsdns.net
- 云台单片机控制程序模拟内有云台控制软件非常的还用-PTZ microprocessor control program simulation PTZ control software is also used very
MotorStepper-aHI3507-board
- HI3507 IPCAM 云台控制程序代码。主要使用单片机STC11L08XE控制电机驱动实现云台控制，通过串口实现与CPU通信。-The HI3507 IPCAM PTZ control code. Mainly use the microcontroller STC11L08XE control motor drive PTZ control, communication through the serial port to ach
_046
- 云台控制程序（PID控制无刷电机）（使用arduino0-PTZ control procedures (PID control brushless motor) (arduino0
PTZ-control-procedures
- 云台控制程序，可以实现控制云台控制镜头与灯光等-PTZ control procedures, can control PTZ control lens and lighting, etc.
VideoTenbo
- windows 版摄像头控制程序,带云台控制，云台控制编码-windows version of camera control program, with PTZ control, PTZ control coding
2-degrees-of-freedom-PTrar
- 改程序是博创公司生产的机器人上的，关于2自由度云台的控制程序，改程序是VC编写的-Reform program is produced by Borch on the robot, about two degrees of freedom PTZ control program, change the program is written in VC
o323bgc-release-v090-v20160110
- 毛子最新BGC云台控制程序,固件+源代码-BGC firmware project
yuntaicontrol
- VC编写的云台控制程序，通过串口控制，已通过编译-VC write yuntai control procedures, through a serial port control, has passed the compilation