搜索资源列表
用MSP430单片机构建温度采集报警系统
- 温度采集系统主要通过温度传感器MAX6613采集得到温度数据,MSP430F149作为CPU从温度传感器读取数据,将得到的数据进行判断然后做出相应的处理,比如显示或者报警。由于MSP430F149片内集成了A/D转换通道,这样可以直接将单片机的A/D输入通道与传感器的模拟电压输出通道相连接。另外系统通过键盘输入来完成对报警温度的上限和下限的设置,通过显示电路将得到的数据显示出来,当温度超过上限和下限的时候,系统进行报警,报警时通过驱动一
WL024_ADC0832数字电压表LED显示
- 控制ADC0832做数据采集,并用数码管显示出来,搞测控的朋友可以-control data acquisition, control and digital display and control of engaging friends can play
AD0809
- 数字电压表,实现0-5V的电压采集。 比较简单的-Digital voltage meter to achieve 0-5V voltage acquisition. Relatively simple
jianyidianyabiao
- 用AD0809的电平转换数据采集,实现8路电压的循环检测-AD0809 level with the conversion of data acquisition, 8-way to achieve the cycle of voltage detection
51-single-chip-proseor
- 基于51单片机的温度和电压采集与循环显示的控制程序,其中温度传感器为LMA95,采用I2C总线传输,显示器为8段LED数码管-51 single-chip-based temperature and voltage of the cycle of acquisition and display of the control procedures, including temperature sensors for LMA95, usin
MAX532
- max235芯片程序,实现电压采集,51单片机,1602显示电压值,精确度为0.001-max235 chip program, the voltage acquisition, 51 SCM, 1602 shows the voltage with an accuracy of 0.001
ADC_V
- 一个简单的电压采集程序,可以作为电压表-A simple voltage acquisition program can serve as a voltage meter ..
51ad
- 基于51单片机的8路AD电压采集与测量 用LCD对8路电压进行显示 用ADC0809对信号进行AD转换-Based on MCU 51 8 AD-voltage collection and measurement of the 8 voltage LCD display with ADC0809 AD converter on the signal. . .
voit
- 本例利用ADC0809 的A/D 转换原理,将被测的多路模拟量转换成数字量,并 用数字方式显示测量结果。本系统以单片机AT89C52 为系统的控制核心,结合A/D 转换 芯片ADC0809 设计一个多路电压采集系统,其中A/D 转换结果经过AT89C52 处理,最后 通过数码管显示相应的数值。本系统通过一个按键可以选择8 路0-5V 之间的直流电压 值进行测量,并在四位数码管上显示相应的数值。读数据准确,测量方便。-In
1111
- 多路电压采集-Multi-voltage acquisition. . . . . . . . . . . . . . . . . . .
PCF8591
- PCF8591 AD电压采集仿真程序 电压表仿真设计 PCF8591模拟量采集(PCF8591 AD voltage acquisition simulation program, voltmeter design simulation, PCF8591 analog acquisition)
实验17 ADC实验
- STM32F1的ADC电压采集。。。。。。(ADC voltage acquisition of STM32F1)
电压检测2
- 四路电压监测,四路电压采集,并通过串口2将采集到的电压数据发出(Four voltage monitoring, four voltage acquisition, and through the serial port 2 will be collected voltage data)
模拟电压采集
- 通过单片机采集模拟电压,经过转换之后,把信号送给VB,显示出来(The analog voltage is collected by the single chip microcomputer. After the conversion, the signal is sent to the VB, and the signal is displayed.)
0-5V电压采集main
- 0-5V电压采集,串口数据传输,可以转USB接口(0-5V voltage acquisition, serial data transmission, can transfer USB interface)
17-ADCO电压采集-PA0
- 在8M晶振下,实现ADC0电压采集,简单易用,逻辑清楚。(The realization of ADC0 voltage acquisition under the 8M crystal oscillator)
综合检测电压
- 实现了基于stm32的ADC电压采集,在野火平台上改进代码(ADC voltage acquisition based on STM32 is realized.)
STC15W408AS电压采集装置
- 基于STC15W408AS单片机进行电压采集装置,并且进行电压 的记忆,完整程序可直接下载。(Based on STC15W408AS MCU, the voltage acquisition device is implemented, and the voltage memory is carried out. The complete program can be downloaded directly.)
labview
- 创建虚拟采集卡 等待直至完成 电压采集系统 应变测量(Create a virtual acquisition card wait until completed voltage acquisition system the strain measurement)
电压采集
- 编写的可以进行电压采集的LABVIEW小程序(Voltage acquisitionA LABVIEW Program for Voltage Collection)