搜索资源列表
IR_MEGA8_1_5
- 用MEGA8实现4路红外调制发射接收的源码-4-way with MEGA8 realize infrared transceiver modulation source
FrequenzzaehlerV0_1
- 自己制作51开发板. 带自恢复保险丝,试验安全,40Pin锁紧插座适用于4~40脚芯片,可以自由配置电源引脚。 板上资源: 1、6个高亮数码管显示(数字和字母显示) 2、8个独立优质按键(2Pin)(人机接口输入) 3、8个高亮发光二极管(跑马灯、指示灯、红绿灯等) 4、标准的RS232通信接口(PC通信) 5、一体化红外接收头(高灵敏度) 6、遥控器用红外发射管(广发射 角)可以模拟遥控器。 7、蜂
Infraredremote-controlelectroniccodelock
- 本系统采用单片机8051作为本设计的核心元件,利用红外线遥控原理和单片机串行发射、接处等功能而设计的一款有本机开锁和遥控开锁的电子密码锁。-The system uses a single-chip 8051 as a core component of this design, the use of infrared remote control theory and single-chip serial launch, then t
hw
- 红外发射接收,控制,试验,是理想的教学,学习,开发伙伴-Infrared emission to receive, control, testing, is ideal for teaching, learning, development partners
Learningremotecontrol
- 单片机设计的遥控电路,遥控码的脉宽数用红外线接收器解码后送单片机读入,发射时由单片机产生40KHZ红外调制信号送红外线发射管发射-Single-chip design of the remote control circuit, remote control code number of the pulse width decoder using infra-red receiver to read single-chip evacua
jj
- 红外遥控器已被广泛使用在各种类型的家电产品上,它的出现给使用家器提供了很多的便利。红外遥控系统一般由红外发射装置和红外接受设备两大部分组成。红外发射装置又可由键盘电路、红外编码芯片、电源和红外发射电路组成。红外接收设备可由红外接收电路、红外解码芯片、电源和应用电路组成。通常为了使信号能更好的被传输发送端将基带二进制信号调制为脉冲串信号,通过红外发射管发射。本设计采用Atmega8作为红外发射编码和接收解码芯片。-Infrared rem
InfraredLaunchingAndReceiving
- 红外遥控器是由发射部分和接收部分组成的,它的基本功能是在发射部分按一个键,在接收部的数码管上显示对应的键(0~9)。 -Infrared remote control is part of the launching and receiving components, and its basic function is to launch some of the press of a button, the Digital
Speed-infrared-instrument
- 红外线转速仪,利用红外线的发射、反射原理,结合单片机的强大控制来实现。-Speed infrared device, the use of infrared emission, reflection, combined with powerful single chip to achieve control.
1234(2)
- 接收译码电路由红外接收放大器、音频译码电路和声控执行电路组成。接收红外二极管应采用与红外发射管配对的管,在收到红外光脉冲后,接收管D1的两极间电阻作与频率相应的变化,由光信号转化为电信号,经VT1和IC1放大-Received by the infrared receiver decoding circuit amplifier, the audio decoding circuit and voice-activated circui
Upload_DownFiles_
- 红外发射接收管典型应用接口电路,包括原理图-Infrared receiver tubes typical applications, including schematics
nec
- C写的 nec芯片的 红外遥控器的发射 解码程序 51单片机 -C write nec chip infrared remote control launching decoding program 51 MCU
HONGWAISHOUFA
- 红外收发演示,红外测试程序,用单片机通过发射管发射38K的调制频率码,由一体化接收并解码由发光管显示-Infrared transceiver demo, infrared testing program, microcontroller through the launch tube with the launch of 38K code modulation frequency, from integration to receiv
fashe
- 可以启动红外发射头,产生38Khz红外信号,以启动VS0038接收头,接收信号-c language program
yaokong
- 基于单片机的红外遥控发射程序。。用c语言编程-Infrared Remote Microcontroller-based program. . With c language programming
红外解码
- 红外解码,对常用红外遥控发射芯片UPD6121G进行解码,根据接收到波形显示其 32位二进制红外编码数据波形,根据波形下方刻度可查阅每一位为0或1(Infrared decoding, commonly used infrared remote control chip UPD6121G chip decoding, according to receive the waveform display 32 bit binary in
stm8s003__V01_IAR
- 采用stm8s003设计的红外发射控制灯程序,此程序已经经过实践,符合要求。(Stm8s003 design of infrared emission control lamp procedures)
发射端程序
- 控制红外遥控器的发射不同频率不同时间的信号(Control the emission of infrared remote control)
红外线遥控Proteus仿真电路+发射+接收程序
- 基于单片机控制平台的用于红外无线遥控控制编码(Infrared wireless remote control coding based on SCM control platform)
20-红外遥控同时发射接收程序
- 红外遥控同时发送接收程序u,内含C和汇编两种语言(Infrared remote control simultaneous sending and receiving program u, containing C and assembler two languages)
28. 红外遥控实验
- 红外遥控器发射红外键值的编码信号,通过红外接收头进行解码,并将解码后的数据通过串口打印(Infrared remote controller emits a coded signal of infrared key value, decodes it through an infrared receiver, and prints the decoded data through a serial port.)