资源列表
[单片机(51,AVR,MSP430等)] LED_controlled_by_keys
说明:程序实现如下模拟彩灯,开发板从左至右4个按键分别为S1-S4,从上至下8个灯为L1-L8,按下S1键8只LED小灯以1HZ频率闪烁,按下S2键8只灯奇偶交替点亮,间隔0.3S,按下S3键,L1-L4与L5-L8灯交替点亮,间隔0.2s,按下S4键熄灭所有灯。-Lantern simulation program to achieve the following development board left to right are four buttons S1-S4, top to bot<张平华> 在 2025-11-23 上传 | 大小:1kb | 下载:0
[单片机(51,AVR,MSP430等)] pinlvji
说明:频率计在上电后,具有:能测试1-100HZ的低频信号;并把结果显示在数码管上。误差小于1HZ。-After power-frequency meter, comprising: a low-frequency signal to test the 1-100HZ and the results are displayed on digital tube. Error is less than 1HZ.<张平华> 在 2025-11-23 上传 | 大小:1kb | 下载:0
[单片机(51,AVR,MSP430等)] xinhaofashengqi
说明:按下S1从单片机第1个引脚上输出频率为1KHz的方波,再按下S1则停止输出方波; 方波频率误差小于1 。 晶振频率:11.0592MHz-Press S1 output the first one on the microcontroller pins 1KHz square wave frequency, and then press the square wave output S1 is stopped Square-wave frequency error is less<张平华> 在 2025-11-23 上传 | 大小:1kb | 下载:0
[单片机(51,AVR,MSP430等)] stopwatch
说明:数码秒表设计:开发板上4键从左至右为S1-S4,上电后,开始时显示 0.0 ; 利用S1按键后启动计时;S2按键后停止计时;S3按键后计时归零;最大计时 为9.9秒。计时误差小于0.2秒,显示稳定。 晶振频率:11.0592MHz -Digital stopwatch design: 4 key development board left to right S1-S4, after power is displayed at the beginning of 0.0 S<张平华> 在 2025-11-23 上传 | 大小:1kb | 下载:0
[单片机(51,AVR,MSP430等)] daojishi_miaobiao
说明:倒计时秒表设计:使秒表在上电/复位后,具有:开始时显示 9.9 ;并开始倒计时, 当9.9S计时到,数码管显示0.0并闪烁,同时蜂鸣器发声报警3S,倒计时误差小于0.2秒。 晶振频率:11.0592MHz-Countdown stopwatch design: stopwatch after power-on/reset, comprising: a display at the beginning of 9.9 and begins the countdown, When t<张平华> 在 2025-11-23 上传 | 大小:1kb | 下载:0
[图形图像处理(光照,映射..)] fastPCA0094
说明:快速主成分分析算法,经测试要比传统PCA快很多。-Fast principal component analysis algorithm has been tested much faster than the traditional PCA.<enzo> 在 2025-11-23 上传 | 大小:1kb | 下载:0