资源列表

« 1 2 ... .33 .34 .35 .36 .37 3738.39 .40 .41 .42 .43 ... 216394 »

[图形图像处理(光照,映射..)matlab灰度图象缩小实验

说明:实现了基于MATLAB的灰度图像缩小,可通过修改程序获得想要的性质(Reduction of gray image based on MATLAB.The desired nature can be obtained by modifying the program.)
<LV135> 在 2025-11-23 上传 | 大小:40kb | 下载:0

[其他小程序dq

说明:联合运行,1个手环的输入输出信息,读取其中各类信息(Joint operation, input and output information of one bracelet, reading various information therein)
<沐涵> 在 2025-11-23 上传 | 大小:1kb | 下载:0

[其他小程序sc

说明:对信息进行读取输出,打印在窗口上面,还是联合文件(Read output of information and print it on the window)
<沐涵> 在 2025-11-23 上传 | 大小:3kb | 下载:0

[其他小程序bx

说明:并行处理,交互和去区分这些手环的ID并且能够分别实现功能(This sample illustrates how to interface with multiple armbands and distinguish between them.)
<沐涵> 在 2025-11-23 上传 | 大小:1kb | 下载:0

[其他小程序GT21L16S2W驱动程序

说明:完整的字库驱动代码,方便移植使用,测试通过!(Complete font drive code)
<明礼> 在 2025-11-23 上传 | 大小:625kb | 下载:0

[串口编程pjocesss_delegate

说明:OFDM通信仿真 可计算OFDM通信误码率,图形显示()
<pxscqnh> 在 2025-11-23 上传 | 大小:11kb | 下载:0

[其他小程序滤镜Android-DEMO

说明:磨皮美白算法接口文档 1. XIUSDK_SoftSkin420 2. XIUSDK_SoftSkinBGR 3. 滤镜ID(XIUSDK Photo Filter 1. XIUSDK_SoftSkin420 2. XIUSDK_SoftSkinBGR 3. FilterID)
<ChanChun> 在 2025-11-23 上传 | 大小:1.5mb | 下载:0

[Internet/网络编程syvpsrot

说明:OFDM降低峰平比采用预失真技术,程序仿真了加入预失真技术后的星座图与未加预失真的比较,结果比较明显,采用QAM映射,()
<pxscqnh> 在 2025-11-23 上传 | 大小:6kb | 下载:0

[其他小程序xiaodong

说明:处理全部信息,然后按照自己要求的进行输入输出,仅适用于这类手环(Handle all the information, then input and output according to your own requirements, only for the bracelet)
<沐涵> 在 2025-11-23 上传 | 大小:39.57mb | 下载:0

[其他小程序AVL-CRUISE-2014-整车经济性动力性分析操作指导书

说明:AVL-CRUISE-2014-整车经济性动力性分析操作指导书(AVL-CRUISE-2014- vehicle operation guidance for economic dynamic analysis.)
<七七七仔> 在 2025-11-23 上传 | 大小:6.43mb | 下载:1

[单片机(51,AVR,MSP430等)IIC

说明:使用数码管和AT24C02实现: 1、数码管从0显示到99,溢出后从0循环显示,时间间隔为一秒。 2、显示到某个数时突然关闭电源,AT24C02将保存当前的数字。 3、重新启动后数码管会接着上次的数继续显示(Using digital tube and AT24C02 implementation: 1, the digital tube displays from 0 to 99. After overflow, it displays from 0 cycles, w
<菜鸟一枚001> 在 2025-11-23 上传 | 大小:29.34mb | 下载:0

[行业应用软件Untitled5

说明:风力机叶片设计程序,可以计算直径攻角,可出叶片(The design procedure of wind turbine blade can calculate the attack angle of diameter and leave the blade.)
<heizi_hz> 在 2025-11-23 上传 | 大小:1kb | 下载:0
« 1 2 ... .33 .34 .35 .36 .37 3738.39 .40 .41 .42 .43 ... 216394 »

源码中国 www.ymcn.org