资源列表
[单片机(51,AVR,MSP430等)] 读电机码盘的程序
说明:读取一个电机码盘信号,里面有对串口读写,对控制寄存器读写的代码。入门级!-read a motor encoder signals, and they read and write to serial port, the control register read and write code. Entry-level!<张雪> 在 2025-06-05 上传 | 大小:12kb | 下载:0
[单片机(51,AVR,MSP430等)] mm36sb020
说明:mm36sb020存储器与单片机连接时的读写程序!里面还包含了与单片机的接口!-mm36sb020 They also include interface with microcontroller!<士大夫> 在 2025-06-05 上传 | 大小:3kb | 下载:0
[单片机(51,AVR,MSP430等)] 单片机主板监控程序
说明:系统的最小板程序,可以作为其他开发的基础!可以通过键盘控制!-the smallest board procedures, can be used as the basis for other development! Keyboard control can!<士大夫> 在 2025-06-05 上传 | 大小:1kb | 下载:0
[单片机(51,AVR,MSP430等)] 电机调速控制程序
说明:电机调速的控制程序,你可以通过这个程序来设定参数,通过反馈就可以控制速度了啊!-of motor speed control procedures, you can use this procedure to set parameters, feedback can control the pace of their ah!<士大夫> 在 2025-06-05 上传 | 大小:2kb | 下载:0
[单片机(51,AVR,MSP430等)] 电梯控制程序
说明:把程序写进单片机从而控制电梯的上下,开关门,报警等功能!这个程序简单,使用性强!-procedures written into the MCU control of the elevator up and opening the doors, alarm functions! This simple procedure, the use of strong!<士大夫> 在 2025-06-05 上传 | 大小:2kb | 下载:0
[嵌入式/单片机编程] doc_ucosii_data_m8_iccavr_by_yfang2
说明:ucos-ii 编译器ICCAVR CPU atmega8 8M 晶振 对原作者的ucos进行了简化,去掉了 hook,保留了基本功能 代码精简,编译后代码占 mage8 的 49% 时钟使用timer2,中断时间为2 ms 任务1:刷新LED,检测按键,调整时间 任务2:计时,串口发送 9600 bps--UCOS-II compiler ICCAVR. It simplifies original UCOS by removing hook, but it keeps basic funct<*> 在 2025-06-05 上传 | 大小:446kb | 下载:0
[单片机(51,AVR,MSP430等)] 实时时钟-单片机
说明:采用定时器中断的方法,设计一个一天24小时进制的实时时钟;用6个发光二极管分别显示时、分、秒的记时; 能进行整点报时。可以从键盘中预置、修改时钟值。含有硬件设计图-timer interruption using the method to design a band 24 hours a day in real-time clock; With six light-emitting diodes showed the hours, minutes, and seconds to the ent<刘印亮> 在 2025-06-05 上传 | 大小:43kb | 下载:0
[DSP编程] DSP各种应用实例1
说明:英文版。关于DSP一些应用的介绍。包括:Motor Control、Digital Cellular Basestations、ADSL-English. Some of the DSP application presentation. : Motor Control, Digital Cellular Basestations, ADSL<shao> 在 2025-06-05 上传 | 大小:395kb | 下载:0