资源列表

« 1 2 ... .45 .46 .47 .48 .49 28850.51 .52 .53 .54 .55 ... 33928 »

[单片机(51,AVR,MSP430等)num-_change

说明:用汇编编写的进制转换器。16进制、10进制和二进制之间相互换算,二进制有LED灯显示,有超量程报警功能,有功能提示(LED数码管),基于C8051F310 -Written in assembly hex converter. Hexadecimal, mutual conversion between decimal and binary, with LED lights display, there is over-range alarm function, a function pro
<> 在 2025-06-11 上传 | 大小:44kb | 下载:0

[VHDL编程usb_sim_model

说明:EZ-USB的仿真模型,Verilog实现,能够实现端点传输,自用。-EZ-USB simulation model, Verilog implementation, to achieve the endpoint transmission, personal use.
<爱阳阳> 在 2025-06-11 上传 | 大小:2kb | 下载:0

[VHDL编程i2c_slave

说明:Verilog实现的i2c从设备仿真模型,只需修改控制码就可直接使用,自用-Verilog implementations i2c slave device simulation models, simply modify the control code can be used directly, for personal use
<爱阳阳> 在 2025-06-11 上传 | 大小:5kb | 下载:0

[VHDL编程M25P128_model

说明:M25P128(NOR FLASH)的仿真模型,Verilog实现,调试了很久才通,现在基本功能完整,仿真时打印调试信息,自用无问题。-M25P128 (NOR FLASH) simulation model, Verilog implementation, commissioning a long time to pass, and now the basic functions of a complete, print debug information during simulation,
<爱阳阳> 在 2025-06-11 上传 | 大小:12kb | 下载:0

[VHDL编程jsq

说明:基于FPGA的计算器,可以实现加减乘除运算功能,由于时间问题,浮点运算未能实现,其中的二进制与BCD码相互转换的模块可以使用-FPGA-based calculator, arithmetic calculation function can be achieved, due to time issues, floating-point operations failed to achieve, including binary and BCD code conversion modules t
<> 在 2025-06-11 上传 | 大小:1.16mb | 下载:0

[VHDL编程nor_flash_core

说明:Verilog实现的NOR FLASH控制器,基于M25P128开发,功能完整,简洁易懂,自用无问题。-Verilog implementations NOR FLASH controller, based M25P128 development, full-featured, easy to read, for personal use, no problem.
<爱阳阳> 在 2025-06-11 上传 | 大小:4kb | 下载:0

[其他嵌入式/单片机内容7segment

说明:THIS IS A PROGRAM FOR 8051 ON LIEL SOFTWARE TO ACCESS 7 SEGMENT AND DISPLAY DESIRE NUMBERS ON 7 SEGMENT DISPLAY. IN 7 SEGMENT, 8 LED ARE RESPONSIBLE FOR DISPLAYING ANY NUMBER WHICH ARE CONTROLLED BY MICROCONTROLLER. YOU CAN USE THIS LOGIC ON MANY OTH
<pawanesh> 在 2025-06-11 上传 | 大小:1kb | 下载:0

[单片机(51,AVR,MSP430等)SRC

说明:用三星单片机写的电热毯控制程序,有数码管显示温度,有温度控制功能和定时功能,已批量使用。-Using Samsung MCU write blanket control program, there are digital display of temperature, temperature control function and timing functions, have been used in batches.
<陈良富> 在 2025-06-11 上传 | 大小:66kb | 下载:0

[单片机(51,AVR,MSP430等)source

说明:温度仪表通用程序,可检测热电偶和CU50。程序带有PID控制算法和PID参数自整定算法。-General procedure can detect the temperature meter, thermocouple and CU50. The program with a PID control algorithm and the PID parameters self-tuning algorithm.
<陈良富> 在 2025-06-11 上传 | 大小:36kb | 下载:1

[单片机(51,AVR,MSP430等)SOURCE

说明:门禁系统单元门口控制系统,提供与每个房间的485呼叫通信,控制单元门的开关和管理-Access control system units gate control system, and each room provides 485 call communication, switching and management control unit door
<陈良富> 在 2025-06-11 上传 | 大小:17kb | 下载:0

[单片机(51,AVR,MSP430等)081104

说明:使用义隆低成本单片机的感应灯程序,专用于保险箱内,低功耗。当保险箱打开时提供光源和发出感应信号-The use of Elan low cost microcontroller induction lamp program, dedicated to the safe, low power. When the safe is opened to provide light source and sends an induction signal
<陈良富> 在 2025-06-11 上传 | 大小:2kb | 下载:0

[单片机(51,AVR,MSP430等)SRC

说明:热量表通用程序,检测水管流量和进水管-出水管温度差,用于热量的累积。-The general program of heat meter, water flow and the water inlet pipe detection- outlet temperature difference for heat, accumulation.
<陈良富> 在 2025-06-11 上传 | 大小:136kb | 下载:0
« 1 2 ... .45 .46 .47 .48 .49 28850.51 .52 .53 .54 .55 ... 33928 »

源码中国 www.ymcn.org