资源列表
[VHDL编程] ninek468c
说明:基于FPGA的IP模块程序,包括数字输入输出控制,寄存器控制和访问-IP MODULE<yinchengjun> 在 2025-11-21 上传 | 大小:6kb | 下载:0
[其他嵌入式/单片机内容] Embeddedsystemsarchitectureprogramminganddesign.ra
说明:嵌入式系统——体系结构,编程和设计 里面详细讲解了嵌入式的硬件,操作系统和设计例子。这本书非常适合嵌入式系统入门人员和嵌入式系统软硬件开发人员使用。-Embedded systems architecture,programming and design,it consist of embedded system hardware, operating systems and design example.And it is suitable for embedded system engine<聂静涛> 在 2025-11-21 上传 | 大小:21.74mb | 下载:0
[其他嵌入式/单片机内容] avr_uart_utility
说明:AVR UART examnple showing interrupt and pulling based UART.<Aaron> 在 2025-11-21 上传 | 大小:2kb | 下载:0
[单片机(51,AVR,MSP430等)] avr_16x2_lcd_driver
说明:AVR LCD 16x2 driver showing how to read/write to an LCD through an AVR chip. The lcd uses either an 8 pin or 4 pin interface.<Aaron> 在 2025-11-21 上传 | 大小:2kb | 下载:0
[uCOS开发] ucos-iiv2.52sourceprogram
说明:压缩包中包含了ucosiiv2.52操作系统的各个源程序,种类齐全。-This document consists of all part sources of ucosiiv2.52 operating system.<聂静涛> 在 2025-11-21 上传 | 大小:71kb | 下载:0
[嵌入式Linux] Thebasicinstructionoflinux
说明:此压缩包中含有的WORD中含有着Linux系统中常用的命令。-This word file has detail basic instruction of linux operating system<聂静涛> 在 2025-11-21 上传 | 大小:42kb | 下载:0
[单片机(51,AVR,MSP430等)] cordic
说明:此段程序为CORDIC的实现,参照论文加速CORDIC算法的实现-CORDIC implementation procedures for this section, reference to paper to accelerate the realization of CORDIC Algorithm<LILI> 在 2025-11-21 上传 | 大小:1kb | 下载:0
[单片机(51,AVR,MSP430等)] F340_ad
说明:例程说明,本程序是c8051f340对电位器产生的电压值进行采样,可以在寄存器观察AD的 也可以通过LCD将值显示出来,由于LV595芯片片选引脚与以太网控制芯片CP2200 中断引脚复用因些在此例程中加入了将CP2200芯片中断关闭的代码。件-Routine descr iption of the potential of this program is c8051f340 voltage generated by sampling can be observed in the AD<马佳智> 在 2025-11-21 上传 | 大小:11kb | 下载:0
[微处理器(ARM/PowerPC等)] BasedonARMandVS1103btheMIDIaccompanimentsystem
说明:基于ARM和VS1103b的MIDI伴奏系统设计Based on ARM and VS1103b the MIDI accompaniment system-Based on ARM and VS1103b the MIDI accompaniment system<beijing002> 在 2025-11-21 上传 | 大小:388kb | 下载:0
[单片机(51,AVR,MSP430等)] LCDWNL
说明:*日历时钟 * *按K1,进入设置状态 * *按k2,停止闹钟声音 * *按k3,依次进入闹钟功能是否启用,闹钟时,分秒,年,月,日及时间时,分,秒的设置, * *直到退出设置状态 * *按k4,调整是否起用闹钟和调节闹钟时,分,秒,年,月,日,时间的时,分,秒的数字 * *LCD第二排中间显示小喇叭,表示启用闹钟功能,无则禁止闹钟功能 * *(可在调整状态进行设置) * *正常状态,LCD上排最前面显示自定义字符,LCD下排最前面闪动"XUELIN" * *<gaozhe> 在 2025-11-21 上传 | 大小:5kb | 下载:0