资源列表

« 1 2 ... .49 .50 .51 .52 .53 29854.55 .56 .57 .58 .59 ... 33928 »

[VHDL编程lab3NHHT

说明:Lab Project On MISP single cycle implementation
<Anh Tuan> 在 2026-01-15 上传 | 大小:331kb | 下载:0

[VHDL编程FileRecv

说明:卷积编码的有关介绍,有关论文,以及有关matlab程序代码-Convolutional code introduced the paper, as well as the Matlab code
<钟鑫> 在 2026-01-15 上传 | 大小:1.27mb | 下载:0

[VHDL编程shizhong

说明:fpga时钟程序FPGA Design - Best Practices-FPGA Design- Best Practices
<李宁> 在 2026-01-15 上传 | 大小:485kb | 下载:0

[VHDL编程VGA

说明:VGA实验 FPGA Design - Best Practices- FPGA Design- Best Practices
<李宁> 在 2026-01-15 上传 | 大小:427kb | 下载:0

[VHDL编程IIC

说明:IIC总线程序设计 FPGA Design - Best Practices- FPGA Design- Best Practices
<李宁> 在 2026-01-15 上传 | 大小:612kb | 下载:0

[VHDL编程Verilg-135samples

说明:verilogHDL程序设计 FPGA Design - Best Practices- FPGA Design- Best Practices
<李宁> 在 2026-01-15 上传 | 大小:112kb | 下载:0

[VHDL编程Goujian

说明:搭建FPGA嵌入式系统 FPGA Design - Best Practices- FPGA Design- Best Practices
<李宁> 在 2026-01-15 上传 | 大小:10.74mb | 下载:0

[单片机(51,AVR,MSP430等)wannianli

说明:单片机万年历程序 基于I2c 总线 自己写的 绝对好用-Absolutely easy to use microcontroller calendar program is based on the I2c bus
<renfeng> 在 2026-01-15 上传 | 大小:77kb | 下载:0

[单片机(51,AVR,MSP430等)test6

说明:使用8155实现对并行接口的扩展。利用8155的PA口输入D1区KEY组各按键的状态信息,然后将该状态信息通过单片机的P1口输出到D1区LED组显示。-8155 to achieve an extension of the parallel interface. 8155 PA port input D1 zone KEY group key state information, and then the state information through the microcontroller
<qingguozhi> 在 2026-01-15 上传 | 大小:1kb | 下载:0

[VHDL编程Ex07

说明:利用ADC0809和DAC0832实现模拟电压信号的采集与输出。-ADC0809 and DAC0832 analog voltage signal acquisition and output.
<qingguozhi> 在 2026-01-15 上传 | 大小:1kb | 下载:0

[单片机(51,AVR,MSP430等)Ex05

说明:定时/计数器实验.利用定时/计数器测量电动机的转速。-Timer/counter experiments. Timer/counter to measure the speed of the motor.
<qingguozhi> 在 2026-01-15 上传 | 大小:1kb | 下载:0

[DSP编程Ex04

说明:利用外部中断输入引脚(以中断方式)控制步进电机的转动。要求:每产生1次中断,步进电机只能步进1步。-External interrupt input pin (interrupt) control the rotation of the stepper motor. Requirements: each generate an interrupt, stepper motor can only step Step 1.
<qingguozhi> 在 2026-01-15 上传 | 大小:1kb | 下载:0
« 1 2 ... .49 .50 .51 .52 .53 29854.55 .56 .57 .58 .59 ... 33928 »

源码中国 www.ymcn.org