资源列表

« 1 2 ... .88 .89 .90 .91 .92 24893.94 .95 .96 .97 .98 ... 33928 »

[嵌入式/单片机编程Flash Disk 优盘制作资料

说明:Flash Disk 优盘制作资料(包括电路原理图源代码)-Flash Disk thumb drive the production of information (including circuit schematics source code)
<飞羽> 在 2008-10-13 上传 | 大小:452.14kb | 下载:0

[嵌入式/单片机编程TMS320x280x__(ADC)

说明:2812的ad的详细说明,包括精度、寄存器等,对大家在配置文件和制板都是很有用的
<宋丹> 在 2008-10-13 上传 | 大小:452.64kb | 下载:1

[嵌入式/单片机编程s3c2443_schematic

说明:S3C2443 Schematic Rev0.2. 参考原理图
<Andy> 在 2008-10-13 上传 | 大小:452kb | 下载:0

[嵌入式/单片机编程ZYN100C开发板C程序

说明:ZYN100C是一款51开发板,针对板卡资源,做了一些易于使用和扩展呢的C库和实例代码。
<zhuyanjun_home@126.com> 在 2009-05-23 上传 | 大小:452.41kb | 下载:0

[微处理器(ARM/PowerPC等)320240(arm)

说明:arm 开发板上液晶模块320240
<xulixia1016@sina.com> 在 2009-04-05 上传 | 大小:452.06kb | 下载:0

[VHDL编程Max232ForHLD3(20040913)(OK)

说明:
<王萌> 在 2025-06-09 上传 | 大小:453kb | 下载:0

[单片机(51,AVR,MSP430等)低功耗设计指南

说明:单片机系统的低功耗设计指南,非常全面的降低单片机系统功耗的方案。(Singlechip system low-power design guide, a very comprehensive program to reduce the power consumption of single-chip system.)
<develop1988 > 在 2025-06-09 上传 | 大小:452kb | 下载:0

[嵌入式LinuxGCC_4_7_0

说明:测试时间,基本的C++程序,可用g++跑通,LINux平台下,用于测试和搭建C++环境(test time LINUX just for test c++ and set up the environment for c++ in linux)
<维克多 > 在 2025-06-09 上传 | 大小:452kb | 下载:0

[嵌入式/单片机编程C#通讯Beckhoff.dll

说明:twincat与c#的通信接口,适合上位机与下位机通讯(The communication interface between programmable logic control and c# is suitable for communication between upper computer and lower computer)
<巫东来 > 在 2025-06-09 上传 | 大小:452kb | 下载:0

[嵌入式/单片机编程液晶显示的DS1302实时时钟

说明:单片机实用项目-液晶显示的DS1302实时时钟,全套素材,代码完整,初学者适用(SCM practical project - LCD DS1302 real-time clock, a full set of materials, complete code, beginners applicable)
<sheepkiki > 在 2025-06-09 上传 | 大小:452kb | 下载:0

[单片机(51,AVR,MSP430等)Test

说明:利用STM8S003F3的ADC功能,读取红外传感器的电压,检测距离,并通过RS485将ADC转换值输出。(Using the ADC function of STM8S003F3, the voltage of the infrared sensor is read, the distance is detected, and the ADC conversion value is output through the RS485.)
<复活之翼 > 在 2025-06-09 上传 | 大小:452kb | 下载:0

[硬件设计[CN0301].通用LVDT信号调理电路_cn

说明:本电路采用AD698 LVDT信号调理器,包含一个正弦波振荡器和一个功率放大器,用于产生驱动原边LVDT的激励信号。AD698还可将副边输出转换为直流电压。AD8615轨到轨放大器缓冲AD698的输出,并驱动低功耗12位逐次逼近型模数转换器(ADC)。系统动态范围为82 dB,带宽为250 Hz,非常适合精密工业位置和计量应用。(This circuit uses the AD698 LVDT signal conditioner, which includes a sine wave osci
<horseplay> 在 2025-06-09 上传 | 大小:452kb | 下载:0
« 1 2 ... .88 .89 .90 .91 .92 24893.94 .95 .96 .97 .98 ... 33928 »

源码中国 www.ymcn.org