资源列表
[单片机(51,AVR,MSP430等)] TLC549
说明:TLC549实现A/D转换的程序,一个8位的a/d 转换,采样及数据存方-TLC549 realize A/D conversion process, an 8-bit a/d conversion, sampling and data-deposit side<amyxxf> 在 2025-10-28 上传 | 大小:2kb | 下载:0
[单片机(51,AVR,MSP430等)] serias_
说明:对读入一个字节(不带回车)读入一个字符串带回车,发送字符串函数测试成功 由于不清楚keil自带的STDIO.H函数是否是堵塞发送接受,所以本程序使用非堵塞方式发送接受,缺点是占 用一些内存,缓冲区大小可自由配置。 -To read into a byte (not back to the car) read into a string back to the car, send the string function to test the success of its own as<talent8791> 在 2025-10-28 上传 | 大小:2kb | 下载:0
[单片机(51,AVR,MSP430等)] vol_1
说明:单片机mp3的音量控制,其P6口各脚分别连接不同的分压电阻,通过改变p6口脚状态,即改变了分压比,-Singlechip mp3<无名> 在 2025-10-28 上传 | 大小:2kb | 下载:0
[单片机(51,AVR,MSP430等)] msp430x11x1_ta_uart9600_04
说明:Descr iption: This program demonstrates a half-duplex 9600-baud UART using // Timer_A3 using no XTAL and an external resistor for DCO ROSC. DCO used for // TACLK UART baud generation. The program will wait in LPM4, echoing back // a received ch<阿化> 在 2025-10-28 上传 | 大小:2kb | 下载:0
[DSP编程] Lab04Float
说明:瑞泰公司TMS320VC33的例程,实验四浮点的基本操作-TMS320VC33 Ruitai company<周铭> 在 2025-10-28 上传 | 大小:2kb | 下载:0
[单片机(51,AVR,MSP430等)] adc
说明:选择RAO做为模拟输入通道; 连续转换4次再求平均值做为转换结果 最后结构只取低8位 结果送数码管的低3位显示 硬件要求:拨码开关S14第2位置ON,第1位置OFF 拨码开关S6全部置ON,S5第4-6位置ON,第1-3位置OFF 为不影响结果,其他拨码开关置OFF。-Select analog input channel for RAO consecutive conversions on average 4 times longer for the resul<michaela> 在 2025-10-28 上传 | 大小:2kb | 下载:0
[单片机(51,AVR,MSP430等)] main
说明:这是一个LCD显示的计算器,能够实现运算功能 -This is a LCD display calculator, computing functions can be achieved<CHEN> 在 2025-10-28 上传 | 大小:2kb | 下载:0
[单片机(51,AVR,MSP430等)] AVR_splc501_mega64
说明:SPLC501在AVR单片机MEGA64上的最简驱动,需要注意的部分有纤细的说明,容易移植!-Mega64 Singlechip SPLC501 in the AVR the most Chien-driven, need to pay attention to some of the notes have thin, easy to transplant!<张子凤> 在 2025-10-28 上传 | 大小:2kb | 下载:0
[单片机(51,AVR,MSP430等)] lcd_128×64
说明:单片机程序及原理图\液晶显示\lcd_128×64 -Single-chip procedure and schematic diagram lcd_128 × 64 LCD<刘好> 在 2025-10-28 上传 | 大小:2kb | 下载:0
[DSP编程] t
说明:完成cnc系统的T曲线控制,较好的完成数控加工-Complete cnc system T curve control, the better to complete CNC Machining<shaojizhou> 在 2025-10-28 上传 | 大小:2kb | 下载:0