资源列表
[单片机(51,AVR,MSP430等)] Basic-C8
说明:51单片机入门程序,四个数码管上分别显示1234-Visual Basic C<张瑞洋> 在 2025-06-08 上传 | 大小:10kb | 下载:0
[单片机(51,AVR,MSP430等)] MSP430__ADXL345
说明:MSP430读取ADXL345加速度传感器上的数据并实时显示在1602上的参考程序(已测试通过)-MSP430 reads the data on the ADXL345 acceleration sensor and displays it in real time on the 1602 reference program.<柯小川> 在 2025-06-08 上传 | 大小:10kb | 下载:1
[单片机(51,AVR,MSP430等)] 24.PWM_zhengxianbo
说明:此为51单片机PWM产生正弦波的c程序,将hex文件烧录到单片机即可。-This is a 51 microcontroller sine wave PWM generated c program, burn the hex file to the microcontroller can.<爱杨> 在 2025-06-08 上传 | 大小:10kb | 下载:0
[单片机(51,AVR,MSP430等)] 23.bujindianji
说明:此为51单片机的步进电机驱动c程序,可将hex文件烧录到单片机使用。-This is the 51 single-chip stepper motor driver c procedures, you can use hex files can be burned to the microcontroller.<爱杨> 在 2025-06-08 上传 | 大小:10kb | 下载:0
[单片机(51,AVR,MSP430等)] SPI_host_half
说明:和泰单片机通信编程设计实例,有通讯需求的程序很好的参考。注意不同序列的差别即可。-Thai microcontroller programming and communication design example, there is a communication program needs a good reference. Note the differences can be different sequences.<oslonwy> 在 2025-06-08 上传 | 大小:10kb | 下载:0
[嵌入式Linux] STM32-duqumpu
说明:stm32f103rct6读取MPU6050六轴的C语言程序-stm32f103rct6 read MPU6050 six axes of C language program<邱玉东> 在 2025-06-08 上传 | 大小:10kb | 下载:0
[单片机(51,AVR,MSP430等)] 0000
说明:八路抢答器该八路抢答器用于8人及8人以下的抢答比赛中,本抢答器实用可靠,采用数码显示器显示抢答编号,具有数码锁存,优先抢答及规定时间内抢答有效的功能。-Eight way responder the eight way responder for 8 and 8 below the answer in the game, the responder is practical and reliable, and using digital display responder numbers, wi<吴婷婷> 在 2025-06-08 上传 | 大小:10kb | 下载:0
[VHDL编程] code
说明:某数据传输系统,试图利用300-3400Hz的话音通 道进行载波传输,波形信道为加性高斯白噪声信道。 –采用线性传输,收发两端拟采用滚降系数0.5的根 号升余弦滤波,以解决采样点失真问题。 –以下仿真采用无记忆采样信道模型,其中受器件限 制,复基带采样点平均功率受限为1,复基带采样 点噪声功率为可调参量-A data transmission system, trying to use 300-3400Hz voice channel for carrier transmission, wave<王先生> 在 2025-06-08 上传 | 大小:10kb | 下载:0
[其他嵌入式/单片机内容] 111
说明:稳压二极管的型号对照,以及稳压二极管的正确使用。-Proper use of a zener diode and Zener diode model comparison table.<lvjingtao> 在 2025-06-08 上传 | 大小:10kb | 下载:0
[微处理器(ARM/PowerPC等)] TIM_EncoderMode
说明:This example shows how to configure the TIM peripheral to interface with a encoder sensor. The TIM3 is configured in encoder mode1: Counter counts up/down on TI2 rising edge depending on TI1 level<guoguo> 在 2025-06-08 上传 | 大小:10kb | 下载:0