资源列表

« 1 2 ... .15 .16 .17 .18 .19 26820.21 .22 .23 .24 .25 ... 33928 »

[单片机(51,AVR,MSP430等)ICCARD

说明:单片机汇编语言编写的IC卡读写程序--IC card read/write program for SCM. It is written in assembly language.
<阿博> 在 2025-09-18 上传 | 大小:5kb | 下载:0

[VHDL编程cuart

说明:verilog编写的全功能串口-verilog programme of serial port
<刘陆陆> 在 2025-09-18 上传 | 大小:5kb | 下载:0

[VHDL编程pipe

说明:verilog编写的流水线模块-Verilog modules prepared by the Pipeline
<刘陆陆> 在 2025-09-18 上传 | 大小:5kb | 下载:0

[单片机(51,AVR,MSP430等)SerialCom

说明:C51 串口通信 包括解析报文-C51 Bunches of communication include the message translating
<Chen> 在 2025-09-18 上传 | 大小:5kb | 下载:0

[单片机(51,AVR,MSP430等)mainp

说明:W78e58读写iButton的源程序,应用于电子门锁的完整程序-W78e58 iButton read and write the source code used in electronic locks integrity procedures
<> 在 2025-09-18 上传 | 大小:5kb | 下载:0

[嵌入式/单片机编程c8051-flash

说明:这是一个C8051FXXX的脉冲发送程序.--Pulse sending program for C8051FXXX.
<谢知非> 在 2025-09-18 上传 | 大小:5kb | 下载:0

[微处理器(ARM/PowerPC等)ARM的开发步骤

说明:比较详细的介绍了ARM的开发步骤同时说明了在开发过程中一些注意事项。-rather detailed account of the development of the ARM with an indication of the steps in the development process for some attention.
<马军> 在 2025-09-18 上传 | 大小:5kb | 下载:0

[VxWorksvxWorksNormal

说明:vxWorks下的DEMO程序。简单示范了任务、信号量、ISR、PIPE等的使用-the DEMO procedures. A simple model of tasks, semaphores, ISR, the use PIPE
<丁一> 在 2025-09-18 上传 | 大小:5kb | 下载:0

[单片机(51,AVR,MSP430等)240128

说明:240128的液晶显示调试程序,供c51开发使用-240,128 LCD debugger, for the development of the use of c51
<谷力民> 在 2025-09-18 上传 | 大小:5kb | 下载:0

[单片机(51,AVR,MSP430等)study_CIP51

说明:c51串口编程的例子,为新手提供好的编程手法和技巧。-decoder serial programming examples for the newcomers to provide good programming practices and skills.
<谷力民> 在 2025-09-18 上传 | 大小:5kb | 下载:0

[单片机(51,AVR,MSP430等)AVR编程C原代码

说明:AVR单片机开发的源代码,对于单片机开发人员有很大的帮助作用。-AVR development of the source code for the MCU developers have been very helpful.
<张磊> 在 2025-09-18 上传 | 大小:5kb | 下载:0

[嵌入式Linux嵌入式系统uclinux编程

说明:总的来说,在uClinux上的开发和标准Linux还是很类似的。通常可以按照下面的步骤去设计和调试: 建立基于以太网的开发环境; 如果所设计的程序和硬件的关联不大,那么一定要在标准Linux上先编译和调试通过。灵活地使用gcc和gdb将大大节省时间; 将x86上的GCC编译好的应用程序用交叉编译工具来编译;如果编译时发现错误,那么很可能存在以下问题: 交叉编译器或库文件的路径不正确;最彻底的解决办法是重新装一次编译器; 遇到库不支持的函数;此时需要自己把函数的实现做成另外一个库供应用程序使用。如
<郭指挥> 在 2025-09-18 上传 | 大小:5kb | 下载:0
« 1 2 ... .15 .16 .17 .18 .19 26820.21 .22 .23 .24 .25 ... 33928 »

源码中国 www.ymcn.org