资源列表
[嵌入式/单片机编程] HT46R24cewen
说明:本系统利用集成智能温度传感器测量温度,采用光纤传输温度信号。系统由单片机(HT46R24)控制温度传感器(DS18B20)的温度采集。当有采集温度的指令的时候,才启动温度传感器并采回其数据,在没有进行温度采集的时候,将通过抬高温度传感器的地,关断其工作电源,如此可以降低系统的功耗。系统将每一次采集回来的数据与前一次的数据比较,若温度变化超限或温升超标,立即发送上述温度值;否则,累加到采集了一定的次数,再向主机发送最新温度值。-The system uses an integrated smart<sxj> 在 2026-01-16 上传 | 大小:1.02mb | 下载:0
[VHDL编程] 61EDA_D994
说明:基于FPGA的 温度传感器 DS18B20接口设计-FPGA DS18B20<碧雪情空> 在 2026-01-16 上传 | 大小:3kb | 下载:0
[嵌入式/单片机编程] ISD1760
说明:通过PIC16F877主控芯片操作ISD1760语音芯片,可以通过手动录音以后实现录音地址的提取。地址计算方法包含在注释中,音质好,可以满足大部分的需求。-PIC16F877 chip operations through the Master ISD1760 voice chip, can be achieved by manually recording after the recording address of the extract. Address calculation metho<sxj> 在 2026-01-16 上传 | 大小:38kb | 下载:0
[嵌入式/单片机编程] PWMtiaoguang
说明:利用定时器产生PWM,控制LED灯由亮到灭,由灭到亮逐步变化,也就是调光现象-The use of timers generate PWM, control the LED light from bright to poverty, from the gradual eradication of the light changes, the phenomenon that is dimming<sxj> 在 2026-01-16 上传 | 大小:10kb | 下载:0
[嵌入式/单片机编程] kaijicishujiyi
说明:每次开机都将次数加1 并存储到EEPROM。这样就能直观的看到机器的使用次数。用P1口 LED做为显示,次数大于256是将溢出,按复位模拟开机 或者直接通过开关开机。-Each boot will add a number of times and stored in EEPROM. This will be able to see the intuitive usage of the machine. As with the P1 port LED display, frequency is<sxj> 在 2026-01-16 上传 | 大小:15kb | 下载:0
[单片机(51,AVR,MSP430等)] a0729e00_3
说明:use for connection to enternet<ali1> 在 2026-01-16 上传 | 大小:372kb | 下载:0
[uCOS开发] uCOS-II2.5.2
说明:Labrosse原版书带的UCOS代码,是学习嵌入式开发的好工具-Labrosse original book with the UCOS code, is a good tool for learning embedded development<xiaoh> 在 2026-01-16 上传 | 大小:1.54mb | 下载:0
[嵌入式/单片机编程] lcd_fast_gpio
说明:this code gives an insight for accessing fast gpio ports in lpc 214x series<pavan> 在 2026-01-16 上传 | 大小:100kb | 下载:0
[DSP编程] C6000optimal
说明:C6000软件优化经验总结 包含了本人日常开发DSP程序过程中总结的若干程序优化方法。-C6000 Software Optimization includes lessons learned from day to day development of DSP I course of the proceedings summarized in a number of procedural optimization.<武忡波> 在 2026-01-16 上传 | 大小:41kb | 下载:0