资源列表
[单片机(51,AVR,MSP430等)] 12864lcd
说明：开关控制128*64lcd并行模式显示，了解单片机控制lcd。-Switch control 128* 64lcd parallel mode shows that understanding the SCM control lcd.<hms> 在 2025-12-31 上传 | 大小：1kb | 下载：0
[单片机(51,AVR,MSP430等)] touch
说明：通过51单片机控制ADS7843的程序，串口通信，附带管脚说明。-SCM control ADS7843 through 51 procedures, serial communication, with pin descr iption.<zhaoweiqi> 在 2025-12-31 上传 | 大小：3kb | 下载：0
[单片机(51,AVR,MSP430等)] 25
说明：DS18B20温度传感器试验程序，其中硬件用到单片机89c51、DS18B20、LCD，用LCD把温度直观地显示出来。-DS18B20 temperature sensor testing procedures, including the hardware used in microcontroller 89c51, DS18B20, LCD, with LCD the temperature visually displayed.<hms> 在 2025-12-31 上传 | 大小：1kb | 下载：0
[单片机(51,AVR,MSP430等)] backup9.4
说明：低功耗msp430单片机的典型源代码，里面有串口，定时器，中断，pwm，adc，等等，对于快速入门很有帮助-The typical low power msp430 microcontroller source code, which has serial port, timers, interrupts, pwm, adc, and so on, useful for the Quick Start<sunyong> 在 2025-12-31 上传 | 大小：223kb | 下载：0
[VHDL编程] modu
说明：this the verilog code that performs the modulus function ... most importantly it is synthesisable... uses the repeated sub algorithm-this is the verilog code that performs the modulus function ... most importantly it is synthesisable... uses the repe<mma32> 在 2025-12-31 上传 | 大小：406kb | 下载：0
[嵌入式/单片机编程] UCOS8051F340
说明：c8051f340 ucos源代码，很好的代码！ -c8051f340 ucos source code, good code!<> 在 2025-12-31 上传 | 大小：243kb | 下载：0
[VHDL编程] nr_divider
说明：This a simple vhdl code that perform division using the non restoring algorithm which is often handy-This is a simple vhdl code that perform division using the non restoring algorithm which is often handy<mma32> 在 2025-12-31 上传 | 大小：1kb | 下载：0
[VHDL编程] PetaLinux_Bootloader_Solutions
说明：A bootloader is required to bring up an FPGA-based Linux system from a power-on or reset. PetaLinux offers a pre-packaged, dual-phase bootloader solution, specially developed and customised for FPGA-based embedded Linux systems.<打狗队> 在 2025-12-31 上传 | 大小：83kb | 下载：0
[嵌入式Linux] System_Settings_Configuration_Menu
说明：The System Settings Configuration Menu is to provide the user with a facility to configure their platform specific settings into the PetaLinux build fr a mework. By using the Kernel Configuration Menu, it allows the user s platform specific settings<打狗队> 在 2025-12-31 上传 | 大小：66kb | 下载：0
[嵌入式Linux] Customising_PetaLinux
说明：A pristine PetaLinux tree only includes pre-configured platform support for Xilinx FPGA based prototype development boards. The user needs to add their platform into PetaLinux before it can be used to build firmware for their target device. Customi<打狗队> 在 2025-12-31 上传 | 大小：104kb | 下载：0
[嵌入式Linux] Debugging_User_Applications
说明：This document describes how to debug user applications under PetaLinux. The GDB debugger (and Insight graphical interface) is available for debugging applications on the MicroBlaze Linux target. To do so, it is first necessary to build the gdbserver<打狗队> 在 2025-12-31 上传 | 大小：135kb | 下载：0