资源列表
[VHDL编程] brentkung_adder
说明:Synopsys的DesignWare库中采用的brentkung高速加法器Verilog源代码生成,附相关文档-Synopsys<zx> 在 2025-10-21 上传 | 大小:510kb | 下载:0
[单片机(51,AVR,MSP430等)] u-pan
说明:基于c8051F320的优盘制作代码及原理图 -C8051F320 the USB-based production code and schematic diagram<侯子> 在 2025-10-21 上传 | 大小:91kb | 下载:0
[微处理器(ARM/PowerPC等)] 11221122
说明:基于S3C44B0X的大型LED显示系统设计-S3C44B0X-based large-scale LED display system design<黄东> 在 2025-10-21 上传 | 大小:112kb | 下载:0
[单片机(51,AVR,MSP430等)] 7843+8279
说明:这个是我在8279上显示触摸屏坐标的程序,十分准确,这个只显示X,Y坐标大小,屏幕大小为192X128.-This is my 8279 touch screen display coordinates procedure is very accurate, this only shows that X, Y coordinates of the size of the screen size of 192X128.<海 明> 在 2025-10-21 上传 | 大小:18kb | 下载:0
[uCOS开发] uCOS_ARM_S3C44B0_code
说明:uc/os-II在s3c44bo下的移植源码-uc/os-II in the transplant s3c44bo source<ygl> 在 2025-10-21 上传 | 大小:117kb | 下载:0
[uCOS开发] Micrium_NIC_LAN91C111
说明:在uCosii操作系统中进行以太网控制芯片lan91c111的控制传输程序,处理器为ADSP BF533芯片-UCosii operating system in the Ethernet control chip to control transmission lan91c111 procedures ADSP BF533 processor chip<lilun> 在 2025-10-21 上传 | 大小:22kb | 下载:0
[uCOS开发] proteus+lcd+ucos_ii
说明:uc/os-II在ARM7的移植,利用Protesu仿真实现的-uc/os-II in the ARM7-transplantation, the use of simulation to achieve Protesu<ygl> 在 2025-10-21 上传 | 大小:321kb | 下载:0
[单片机(51,AVR,MSP430等)] stepping_motor
说明:步进电机起/停,正/反循环控制程序 1.按下一次开关SW2,步进电机顺时针旋转,按下一次开关SW1则停止 再按下一次开关SW2,步进电机反时针旋转,再按下一次开关SW1则停止 重复上述操作,则会出现同样现象 2.按下任意键,退出-Stepper motor starting/stopping, positive/anti-cycle control procedures 1. Pressing a switch SW2, stepper motor clockwise ro<徐翔> 在 2025-10-21 上传 | 大小:2kb | 下载:0
[VHDL编程] VHDL-ram_fifo
说明:VHDL的ram和fifo model code 包含众多的厂家-VHDL the ram and fifo model code contains a large number of manufacturers<SL> 在 2025-10-21 上传 | 大小:1.6mb | 下载:0
[单片机(51,AVR,MSP430等)] yejingkaifa
说明:液晶开发源代码,包含两种12864m的编程,提供proteus仿真运行-LCD development of source code, contains two 12864m programming, providing Proteus simulation run<笔涛> 在 2025-10-21 上传 | 大小:3.5mb | 下载:0