资源列表
[VHDL编程] vivado_LED_Flow
说明:本例程使用vivado2014.4工具,利用xilinx Basys3 实验板实现板载流水灯的两种模式控制。-This project uses verilog HDL to realize the the control of 16 leds loaded on Xilinx Basys3 board.<姚罡> 在 2025-08-02 上传 | 大小:628kb | 下载:0
[VHDL编程] SegSimplified
说明:本工程使用verilog HDL和vivado2014集成开发环境实现利用xilinx Basys3开发板上4位数码管显示从0到9999的计数器功能。-This project uses verilog HDL to realise counting 0 to 9999 on the 7-seg LED loaded on Xilinx Basys3 board.<姚罡> 在 2025-08-02 上传 | 大小:1.15mb | 下载:0
[其他嵌入式/单片机内容] modbus-com
说明:modbus串口调试程序,发送命令给下位机,控制下位机并做出反应-modbus COMM program<wmd> 在 2025-08-02 上传 | 大小:11kb | 下载:0
[DSP编程] SDC_TEST_Core0
说明:blackfin609 裸机读写sd卡,读写模式为spi模式。-read/write sd card on blackfin609 using spi protocol without os<liuping> 在 2025-08-02 上传 | 大小:469kb | 下载:0
[DSP编程] BF707_AZURE_SPI2_FLASH
说明:blackfin707 基于spi1协议的烧写驱动,flash芯片mx系列-blackfin707 burn driver<liuping> 在 2025-08-02 上传 | 大小:1.27mb | 下载:0
[VHDL编程] liushuideng
说明:基于CPLD的流水灯实现,使用VHDL语言编程,闪烁间隔为0.5秒。-CPLD-based water lights to achieve using VHDL language programming, blinking interval of 0.5 seconds.<孙大幕> 在 2025-08-02 上传 | 大小:56kb | 下载:0
[VHDL编程] honglvdeng
说明:基于CPLD的交通信号灯的实现,使用VHDL语言,使用不同颜色的二极管分别代表红黄绿三种信号灯。在数码管上可以分别显示倒计时。-CPLD-based implementation of the traffic lights, the use of VHDL language, using different colors of red yellow and green diodes representing three kinds of lights. On the digital countd<孙大幕> 在 2025-08-02 上传 | 大小:1.04mb | 下载:0
[VHDL编程] bujinji-(kuozhan)
说明:基于CPLD的步进电机控制实现,使用VHDL语言进行编程,通过控制开关,可以实现正转快速,正转慢速,反转快速,反转慢速四种不同的状态。- Based on CPLD stepper motor control implementation using VHDL language programming, by controlling the switch, you can achieve fast forward, slow forward, fast reverse, reverse sl<孙大幕> 在 2025-08-02 上传 | 大小:73kb | 下载:1
[VHDL编程] dianzhen
说明:基于CPLD的实现控制8x8点阵动态显示字母的程序,使用VHDL语言,通过调节分频系数可以实现点阵的变换速度,通过改变不同的状态可以让点阵显示不同的图案。- Based on CPLD for control 8x8 dot matrix dynamic display of letters, the use of VHDL language, by adjusting the division ratio can be achieved by changing the speed dot<孙大幕> 在 2025-08-02 上传 | 大小:258kb | 下载:0
[单片机(51,AVR,MSP430等)] arduino-dial--
说明:基于Arduino单片机为基础的通过串口,控制GSM模块实现两个按键拨打和挂断电话的功能-Arduino-based microcontroller-based through the serial port control GSM module implements two buttons to dial and hang up the phone functionality<ranran> 在 2025-08-02 上传 | 大小:1kb | 下载:0