资源列表

« 1 2 ... .23 .24 .25 .26 .27 33728.29 .30 .31 .32 .33 ... 33928 »

[嵌入式/单片机编程51--spi

说明:51 模拟SPI 51 模拟SPI -SPI 51 simulated mock simulation of SPI SPI 51 51 51 simulated mock SPI SPI 5 a mock simulation SPI SPI 51
<aaa> 在 2008-10-13 上传 | 大小:930byte | 下载:0

[嵌入式/单片机编程CalendarClk

说明:基于时钟芯片DSC12C887的实时时钟系统,显示年月日,时分秒 -DSC12C887 Based on the clock chip real-time clock system, showing date, time Minutes
<MAZEMIN> 在 2008-10-13 上传 | 大小:2.48kb | 下载:0

[嵌入式/单片机编程tempreture

说明:基于DS18B20和RS232的智能温度控制系统,实现温度采集和远程控制-DS18B20 and RS232 based on the intelligent temperature control systems, temperature collection and remote control
<MAZEMIN> 在 2008-10-13 上传 | 大小:29.83kb | 下载:0

[嵌入式/单片机编程down_63

说明:串口程序和移植到MCS51的uCOS_II都是用uV2来运行的-Serial procedures and transplanted to the MCS51 uCOS_II is used to run the uV2
<耿丽> 在 2008-10-13 上传 | 大小:1.29mb | 下载:0

[嵌入式/单片机编程usb_SCH_1

说明:多款USB芯片原理图(ISP1161、ISP1362、ISP1581和D12)-several types of USB chip diagram (ISP1161 and ISP1362. ISP 1581 and D12)
<nahsil> 在 2008-10-13 上传 | 大小:54.19kb | 下载:0

[嵌入式/单片机编程szdzjs_szz

说明:数字电子技术之数字钟课程设计 分析 及其 课程设计报告,对学习数字电子技术的朋友游一定的帮助!-digital electronic technology digital clock curriculum design analysis and design courses, learning digital electronic technology friends YOU can help!
<冬冬> 在 2008-10-13 上传 | 大小:156.69kb | 下载:0

[嵌入式/单片机编程winceGPSGPRS

说明:这个程序包含了wince串口、GPS信号处理,GPRS拨号上网等丰富的内容-This includes the serial wince, GPS signal processing, such as GPRS dial-up Internet access to the rich content
<司文杰> 在 2008-10-13 上传 | 大小:110.07kb | 下载:0

[嵌入式/单片机编程08_gprs

说明:S3C2410上的linux的GPRS驱动程序-S3C2410 the linux GPRS Driver
<jia> 在 2008-10-13 上传 | 大小:9.44kb | 下载:0

[嵌入式/单片机编程keyboardfor2410

说明:在S3C2410上实现linux环境下的键盘驱动驱动程序-S3C2410 in achieving linux environment Keyboard Driver Driver
<jia> 在 2008-10-13 上传 | 大小:5.7kb | 下载:0

[嵌入式/单片机编程11_stepmotor

说明:在S3C2410下实现linux环境下的步进电机驱动程序-in S3C2410 under linux environment Stepper Motor Driver
<jia> 在 2008-10-13 上传 | 大小:158.81kb | 下载:0

[嵌入式/单片机编程sprc097

说明:2812 can参考程序,很不错的,请大家参考学习-2812 can reference procedures, very good, please refer to learning
<李明> 在 2008-10-13 上传 | 大小:239.91kb | 下载:0

[嵌入式/单片机编程USB430CCode

说明:其中的usb端口通信已经作为一个模块来使用,用户只需用以下函数就可以对usb端口进行方便的读写: unsigned char D12_WriteEndpoint(unsigned char endp, unsigned char len, unsigned char * buf) 此为usb端点输出函数,endp是要进行通信的端点,取值为3(普通端点,最大可一次传输16byte)或5(主端点,最大可一次传输64byte);len为一次输出数据长度;*buf为数据所在位置。 usb端点
<刘军> 在 2008-10-13 上传 | 大小:12.39kb | 下载:0
« 1 2 ... .23 .24 .25 .26 .27 33728.29 .30 .31 .32 .33 ... 33928 »

源码中国 www.ymcn.org