资源列表

« 1 2 ... .06 .07 .08 .09 .10 4311.12 .13 .14 .15 .16 ... 33928 »

[嵌入式Linuxtftpd

说明:TFTP服务器配置,此软件可测可用,不需要安装,直接可用,简单方便-TFTP linux loader
<吴松> 在 2025-11-20 上传 | 大小:88kb | 下载:0

[微处理器(ARM/PowerPC等)cshengyin

说明:单片机c语言模仿声音程序,共有警车、救护车、音乐等-SCM c language to imitate a sound program, a total of police cars, ambulances, music
<杨栋> 在 2025-11-20 上传 | 大小:58kb | 下载:0

[微处理器(ARM/PowerPC等)cbujindianji

说明:单片机C语言步进电机的使用原理和控制方法。-Use principle and control stepper motor microcontroller C language.
<杨栋> 在 2025-11-20 上传 | 大小:84kb | 下载:0

[微处理器(ARM/PowerPC等)C-DS1302

说明:单片机C语言DS1302的原理和使用方法。-Principles and methods of use of single-chip C language DS1302.
<杨栋> 在 2025-11-20 上传 | 大小:124kb | 下载:0

[微处理器(ARM/PowerPC等)C-1602

说明:单片机C语言的1602液晶屏的原理和使用方法-Principle 1602 LCD microcontroller C language and methods of use
<杨栋> 在 2025-11-20 上传 | 大小:85kb | 下载:0

[嵌入式Linuxtingting

说明:在zynq板子上实现gps和温度的读取,以及温度传感器的读写-Implement gps and temperature on board zynq read and write temperature sensor
<李昊> 在 2025-11-20 上传 | 大小:18kb | 下载:0

[单片机(51,AVR,MSP430等)key_count

说明:记录按键次数,LED数码管显示按键次数。-Recording keystrokes, LED digital display
<yancy> 在 2025-11-20 上传 | 大小:23kb | 下载:0

[单片机(51,AVR,MSP430等)control_car

说明:ps2手柄控制遥控小车,Arduino手柄接收程序。51单片机小车控制程序。-ps2 handle remote control car, Arduino handle receiver. 51 SCM trolley control procedures.
<yancy> 在 2025-11-20 上传 | 大小:17.02mb | 下载:0

[单片机(51,AVR,MSP430等)ILI9341-16BIT

说明:ILI9341,驱动程序,电压3.3v 51单片机,帮助新手学习tft的驱动-ILI9341, drivers, voltage 3.3v 51 microcontroller, help the novice to learn driving tft
<郑秋生> 在 2025-11-20 上传 | 大小:31kb | 下载:0

[单片机(51,AVR,MSP430等)AiP1616

说明:AIP1616是一款数码管驱动ic,用法简单,使用方便-AIP1616 is a digital driver ic, are easy to use, easy to use
<郑秋生> 在 2025-11-20 上传 | 大小:572kb | 下载:0

[单片机(51,AVR,MSP430等)EXP2_IOkou-xuexi

说明:绘制实验仿真原理图,编写运行程序,实现将十进制数156拆为三个BCD码,并存入30H开始的三个单元,采用汇编语言和C51语言完成。-The simulation draw schematics, write to run the program, to achieve the decimal number 156 split into three BCD, and stores 30H three units started. Subjects were using assembly langu
<李亮> 在 2025-11-20 上传 | 大小:40kb | 下载:0

[单片机(51,AVR,MSP430等)EXP3_jishuqi

说明:P1口做输出口,接八只发光二极管,绘制仿真电路图,硬件连接表见3-1。 ①编写C51程序,采用软件延时的方式实现发光二极管的每秒闪烁。 ②编写C51程序,使8个发光二极管从右到左(上到下)逐一点亮。 ③编写C51程序,使8个发光二极管从两边到中间顺序点亮,直至全部点亮,然后从中间到两边顺序熄灭,直至全部熄灭,如此循环下去。 -P1 port as the output port, then eight light-emitting diodes, circuit simulati
<李亮> 在 2025-11-20 上传 | 大小:45kb | 下载:0
« 1 2 ... .06 .07 .08 .09 .10 4311.12 .13 .14 .15 .16 ... 33928 »

源码中国 www.ymcn.org