资源列表
[matlab例程] Plate_ansys
说明:利用Ansys进行板建模、划分网格,并初步计算,将Ansys的板的M、K导入到Matlab中,进行振动控制分析,并根据阻尼比自动生成阻尼阵C,绘制频率响应曲线,找到最大值,进行比例控制,并给出控制效果-The board using Ansys modeling, meshing, and preliminary calculations, the Ansys board of M, K imported into Matlab, vibration control analysis, damp<skynew> 在 2025-06-09 上传 | 大小:495kb | 下载:1
[matlab例程] RESEARCH_ON_TURBO_EQULIZATION
说明:传统均衡器无法有效地同时对抗这两种信道衰落,而Turbo均衡技术作为一种联合信道均衡和信道译码的方法,能有效地对抗符号间干扰(ISI),提供迭代增益,提高接收机的整体性能。因此,本文根据下一代无线通信系统的设计要求,分别对单载波和OFDM系统的Turbo均衡算法进行了研究。 -Conventional equalizer can not effectively fight both at the same time fading, while the Turbo equalization a<w> 在 2025-06-09 上传 | 大小:687kb | 下载:1
[matlab例程] adaptive_beam
说明:adaptive beamformer using an FFT filter bank with/without DOA estimation and tracking (frequency domain version of Frost beamformer)<terryshi> 在 2025-06-09 上传 | 大小:4kb | 下载:1
[matlab例程] Untitled1
说明:基于FFT谱连续细化算法的高精度频率估计,这种算法可以精确到小数点后两位,这种算法与MUSIC法和ESPRIT法相比,计算量大大降低,而且精度非常高。-This procedure is based on the FFT spectrum continual refinement algorithm s high accuracy frequency, this algorithm may precisely to decimal point latter two, compared the M<hehe> 在 2025-06-09 上传 | 大小:1kb | 下载:1
[matlab例程] Clustering_Coefficient
说明:根据邻接矩阵计算网络的聚类系数。输入为邻接矩阵输出为整个网络的聚类系数-cluster coefficient<h> 在 2025-06-09 上传 | 大小:1kb | 下载:1
[matlab例程] Beam_Vibration_Control
说明:针对梁的振动控制Matlab程序,包括输入MKC矩阵,计算固有频率,并采用Simulink进行梁的振动控制-Matlab for beam vibration control procedures, including input MKC matrix, calculate the natural frequency and vibration of beams using Simulink Control<skynew> 在 2025-06-09 上传 | 大小:72kb | 下载:1
[matlab例程] plot_magnet_line
说明:利用Matlab程序,绘制磁力线,采用三维作图,做出了长方体状磁体的磁力线分布-Matlab program used to draw the magnetic field lines, using three-dimensional mapping, rectangular-shaped magnets made of the distribution of magnetic field lines<skynew> 在 2025-06-09 上传 | 大小:7kb | 下载:1
[matlab例程] matlab_Lab3
说明:information gain calculation in Matlab<Molinken> 在 2025-06-09 上传 | 大小:1kb | 下载:1
[matlab例程] first
说明:二维傅里叶变换,对图像进行二维傅里叶变换处理-Two-Dimensional Fast Fourier Transform The purpose of this project is to develop a 2-D FFT program "package" that will be used in several other projects that follow. Your implementation must have the capabilities to: (a)<solo> 在 2025-06-09 上传 | 大小:1kb | 下载:1