资源列表
[matlab例程] sin-cosinor
说明:利用最小二乘算法自适应跟踪正弦信号时间序列,通常用于分析谐波信号。-Using the least squares algorithm adaptive tracking sinusoidal signal time series, usually used to analyze the harmonic signal.<杨超> 在 2025-09-16 上传 | 大小:2kb | 下载:0
[matlab例程] compute_THD
说明:计算时间信号序列的谐波总畸变率,同时课计算基波的幅值和相位,典型应用于电力信号分析。-The total harmonic distortion signal sequence computation time, while computing the fundamental lesson of the amplitude and phase of the signal analysis is applied to a typical power.<杨超> 在 2025-09-16 上传 | 大小:3kb | 下载:0
[matlab例程] Harmonics_IEC
说明:该函数基于的IEC 61000-4-7标准,计算谐波谱值,需要10分钟测量电压和电流信号,对平均值每10期的测量信号进行谐波分析。-IEC 61000-4-7 standard is based on the function to calculate the value of the harmonic spectrum, takes 10 minutes to measure voltage and current signals, the average of every 10 of the<杨超> 在 2025-09-16 上传 | 大小:9kb | 下载:0
[matlab例程] Cartwright_1999
说明: <Blind phase recovery in general QAM communication systems using alternative higher order statistics> 作者是K.V.Cartwright。文中对以前Chen的算法进行了描述,在此基础上进行了改进。- <Blind Phase recovery in general QAM communication systems using alternative higher orde<hyy> 在 2025-09-16 上传 | 大小:1kb | 下载:0
[matlab例程] cartwright_2005
说明:参考文献是<Blind phase recovery in cross QAM communication systems with the reduced-constellation eighth-order estimator(RCEOE)>,Cartwright,2005 减化为8个正交的点。减化星座法,只利用了8个能量最高的点。从APP方法改进而来,与EOE方法不同。需要进行增益控制。-Reference is <Blind phase recovery<hyy> 在 2025-09-16 上传 | 大小:1kb | 下载:0
[matlab例程] morelli
说明: 该段程序描述了如何去估计多普勒频率变化率。参考文献为Morelli的《Doppler-rate estimation for digital burst transmission》- This section describes how to program the estimated Doppler frequency rate of change. References to Morelli s "Doppler-rate estimation for digital burst tra<hyy> 在 2025-09-16 上传 | 大小:1kb | 下载:0
[matlab例程] Cartwright_2001
说明: 参考文献<blind phase recovery in cross QAM communication systems with eighth-order statitics> 2001,cartwright- References <blind phase recovery in cross QAM communication systems with eighth-order statitics> 2001, cartwright<hyy> 在 2025-09-16 上传 | 大小:1kb | 下载:0
[matlab例程] calculator_rangebyGPS_matlab
说明:利用两点的GPS数值进行坐标转换,然后计算两点之间的距离-The two values for the GPS coordinate conversion, and calculates the distance between two points<张瑞> 在 2025-09-16 上传 | 大小:5kb | 下载:0
[matlab例程] matlab_LFM_pulsecompress
说明:对雷达线性调频信号进行脉冲压缩处理,处理过程中考虑到量化的影响-Chirp radar pulse compression signal processing, process considering the impact of quantitative<张瑞> 在 2025-09-16 上传 | 大小:47kb | 下载:0