资源列表

« 1 2 ... .12 .13 .14 .15 .16 14617.18 .19 .20 .21 .22 ... 15812 »

[matlab例程newton

说明:newton插值算法、三次样条插值算法(包含最大误差计算)-newton interpolation algorithm, cubic spline interpolation algorithm (contains the maximum error calculation)
<ywm> 在 2025-06-22 上传 | 大小:1kb | 下载:0

[matlab例程9160122010

说明:tangent bug is usefull for use it
<soodeh> 在 2025-06-22 上传 | 大小:1kb | 下载:0

[matlab例程LMS

说明:用matlab实现LMS自适应算法,20阶的fir滤波器,自适应效果非常好。-Matlab LMS adaptive algorithm, two order of fir filter, the adaptive effect is very good.
<王岩> 在 2025-06-22 上传 | 大小:1kb | 下载:0

[matlab例程Compressive_gi

说明:We describe an advanced image reconstruction algorithm for pseudothermal ghost imaging, reducing the number of measurements required for image recovery by an order of magnitude. The algorithm is based on compressed sensing, a technique that enables t
<michael zheng> 在 2025-06-22 上传 | 大小:1kb | 下载:0

[matlab例程InterPoints

说明:计算分段三次多项式插值的系数,计算三次样条插值函数的系数组M-Calculating the coefficients of piecewise cubic polynomial interpolation, cubic spline interpolation function calculating the coefficients M
<lsj> 在 2025-06-22 上传 | 大小:1kb | 下载:0

[matlab例程pressure-loss

说明:钻井过程中带有岩屑床的水平井环空压耗计算程序-pressure losses in eccentric annulus
<高中伟> 在 2025-06-22 上传 | 大小:1kb | 下载:0

[matlab例程shiyan

说明:用m序列的自相关性求通道时延,并用延时器进行时延均衡,完成通道校准-With m sequence for channel since the correlation time delay, delay and delay (CCM) equilibrium, complete channel calibration
<小小娟飞飞> 在 2025-06-22 上传 | 大小:1kb | 下载:0

[matlab例程kuopin

说明:信号用m序列进行扩频,成型滤波和BPSK调制后经过信道发送到接收端,接收端进行解扩解调-Using m sequence spread spectrum signal, after forming filter and BPSK modulation channel is sent to the receiver, the receiver to enlarge demodulation
<小小娟飞飞> 在 2025-06-22 上传 | 大小:1kb | 下载:0

[matlab例程gold

说明:生成生数为7,9,10,11的平衡gold码,-Generates raw Numbers for the balance of 7,9,10,11 gold, gold is not so good m sequence code autocorrelation properties, but the same length of two kinds of sequence is more than up to the amount of gold code
<小小娟飞飞> 在 2025-06-22 上传 | 大小:1kb | 下载:0

[matlab例程m_seq1

说明:选择13级移位寄存器的初始数据,用移位加反馈的方法生成级数为3~13的m序列-The selection of the initial data of 13 level shift register, series is generated by shift plus feedback method for 3 ~ 13 m sequence
<小小娟飞飞> 在 2025-06-22 上传 | 大小:1kb | 下载:0

[matlab例程MMS

说明:M/M/是排队系统,不确定对不对,试试吧-M/M/S Queuing system
<GYSD> 在 2025-06-22 上传 | 大小:1kb | 下载:0

[matlab例程phase

说明:phase space of a signal
<marjan> 在 2025-06-22 上传 | 大小:1kb | 下载:0
« 1 2 ... .12 .13 .14 .15 .16 14617.18 .19 .20 .21 .22 ... 15812 »

源码中国 www.ymcn.org