搜索资源列表
SAA7113_init
- GPIO模拟IIC,SAA7113初始化-Analog IIC, SAA7113 Initialization
241000DM9000
- int main (void) { PINSEL0 = (0x00000005)|(0x03<<18) //P0.0 P0.1用作UART PINSEL1 = 0x00000000 //其余为GPIO ReadModuleP() // 读参数 SetNetPort() InitializeInterrupt() InitNic(0) //RTL8019芯片初始化,在
EX08_GPIO
- 对dsp的各个寄存器初始化,及GPIO口的应用-Initialize the various registers on the dsp, and GPIO Mouth
DEMO
- STM32重要初始化文件,其中包括GPIO,RCC,NVIC,TIM,USART等,使用include就是可以使用!-STM32 Configuration
DSP2833x_EPwm
- DSP2833x 初始化GPIO管脚作为ePWM管脚使用。 -This function initializes GPIO pins to function as ePWM pins. Each GPIO pin can be configured as a GPIO pin or up to 3 different peripheral functional pins. By default all pins come up as G
spi-uart
- 这个程序是C8051F30x设备通过 spi 通讯然后从串口发送的例程 具有 spi 跟串口的初始化操作-This program sets up the GPIO pins on the C8051F30x device for the correct functionality, then uses the SPI_Transfer function to send and receiveinformation through
YL3250_kickstart
- kickstart首先做必要的系统初始化,然后将自身代码搬移到IRAM末尾的32K处,搬移大小为0x4000(16K)。之后初始化GPIO并加载stage 1 app到IRAM的首地址处(0x0),并跳转到此处执行。-The kickstart First make the necessary system initialization, its own code and then will move to the end of the
Pro_PWM_for_4
- STM32的程序 里面开了四路PWM可以同时输出 还有基本的初始化 包括时钟 GPIO TIM 等-STM32program to open the four way PWM can simultaneously output and basic initialization includes clock GPIO TIM
IICGPIO
- dspTMS320F2812 模式IIC的GPIO口初始化-dsp mode IIC GPIO port initialization
1_GPIO
- 跑马灯都是你们要接触的第一个程序.对于STM32来说,由于有官方库这种东西的出现,使得原来很麻烦的寄存器初始化变的相对简单.本例程主要让大家感受一下最基本的库操作GPIO 的方法.-Marquees are you want to contact a program for the STM32 is the official repository, the emergence of this kind of thing makes th
Demo--Project
- STM32 实验 模板 含GPIO RCC初始化-STM32 实验 模板 含GPIO RCC初始化
200711-0054-05
- TMS28335初始化完成之后, 1、 先DDS产生73.35hz的方波。(问流量管固定频率) 2、 乘法器的另一个数字端输入乘数直接给一个固定值(按照5v),系数是固定的就是对应PID输出的那个接口,串行十二位信号输出(需要先定好一个GPIO接口)。 3、 再延迟一定的时间0.1s或其他时间之后,开始ad采集信号,分别采两路AD信号,此时不稳定(为什么要等到一定的幅值才开始采集AD信号) 4、 选择250点估计一个频率
stm32l1xx_gpio
- stm32—gpio程序源码,gpio的配置及初始化-the stm32-gpio program source, gpio configuration and initialization
pic_dm
- pic12f617闪灯程序初始化配置 gpio配置-pic12f617 light
u-boot
- 自己写的U-BOOT,目标板为S3C6410,能完成基本的硬件初始化,如GPIO、时钟频率、串口等,引导linux内核的地方有待改进,适合初学者研究,没有官方U-BOOT源码复杂,结构清晰简洁。-Write your own U-BOOT, target board S3C6410, able to complete basic hardware initialization, such as GPIO, clock frequency
adc
- 基于stm32的ADC程序,告诉你如何配置GPIO和时钟的初始化之类的-stm32 adc
SYS_conf
- STM32F407时钟,中断配置头文件,该文件包含HSE,HSI,LSE,LSI,I2S,MCO时钟的初始化; PLL时钟配置,PLL,SYSCLK,HCLK,PCLK1,PCLK2时钟的配置; RCC,GPIO,EXIT,NVIC的配置;-STM32F407 clock, interrupt configuration header file that contains the HSE, HSI, LSE, LSI, I2S,
sys23
- STM32F407时钟,中断,精确延时配置,该文件包含HSE,HSI,LSE,LSI,I2S,MCO时钟的初始化;PLL时钟配置,PLL,SYSCLK,CLK,PCLK1,PCLK2时钟的配置;RCC,GPIO,EXIT,NVIC的配置.-STM32F407 clock, interrupt, precision delay configuration, the file contains HSE, HSI, LSE, LSI, I2S
SPI_FLASH(AT45DB161D)
- 实现SPI FLASH 通信,首先配置GPIO,然后初始化SPI FLASH DRIVER,获得FLASH ID,接着就可以读写SPI FLASH 了-Implement SPI FLASH communications, first configure GPIO, then initialize the SPI FLASH DRIVER, get FLASH ID, and then they can read and write S
dsp28335GPIO-set-clear
- DSP28335的GPIO置位清零方式和初始化程序-The GPIO set DSP28335 cleared the way and initialization procedures