搜索资源列表
lcd_module
- verilog code which receive from uart RX and then output to lcd text display.
qqdengjijisuan
- 自己做来玩的,用来计算跟朋友QQ等级时差的小东西。用了suiPackt和RX控件。图片是定死的,懒得写自动生成代码,有兴趣的朋友可以自己改进
OFDM-basedWirelessBroadBandSystemSimulator
- 基于OFDM的无线宽带系统仿真It contains mainly two parts, i.e. link-level simulator and system-level simulator. Link-level simulator focus on a single-cell single-user scenario, where signal is transmitted from tx, and estimated
Alamouti
- The program simulates alamouti s code with abitrary no.s of rx. Performance analysis can be drawn. (BER vs SNR)
TX_RX
- 在c++builder环境下一个串口通信程序,包括界面的设计和串口通信函数的设计,实现了串口通信。在文件夹TX-RX中。
test05
- UART RX with simple logic flow to check the protocol correct or not. Important is that the logic flow.
905
- NRF905驱动代码 // The content of this struct is nRF905 s initialize data. // CH_NO=1 433MHZ Normal Opration,No Retrans RX,TX Address is 4 Bytes // RX TX Payload Width is 32 Bytes Disable Extern Clock Fosc=16MHZ //
zuoye3
- 中点椭圆法,用画点函数画一个椭圆: 中心(300,400),Rx=200,Ry=150。
zuoye4
- 中点椭圆法,画一个椭圆: 中心(300,400),rx=200,ry=150, 平移到(200,300)旋转逆时针45度
icuwb07submission
- 一个UWB仿真程序包,里面包含信号生成,信道模拟,Tx/Rx等模块。M-file
io
- ecos serial rx and tx
NewMsg-RF1100
- (1) 315、433、868、915Mh的ISM 和SRD频段 (2) 最高工作速率500kbps,支持2-FSK、GFSK和MSK调制方式 (3) 高灵敏度(1.2kbps下-110dDm,1%数据包误码率) (4) 内置硬件CRC 检错和点对多点通信地址控制 (5) 较低的电流消耗(RX中,15.6mA,2.4kbps,433MHz) (6) 可编程控制的输出功率,对所有的支持频率可达+10dBm (7)
msp430x11x1_ta_uart9600_04
- Descr iption: This program demonstrates a half-duplex 9600-baud UART using // Timer_A3 using no XTAL and an external resistor for DCO ROSC. DCO used for // TACLK UART baud generation. The program will wait in LPM4, e
tX+RX+Xmodem
- 标准的c代码,支持Xmodem的接受和发送,支持短线重传,而且随时都可以用ESC断开。功能强大。在4510上可以直接使用。
RX
- cc2500的接收程式,有需的朋友可以参考一下
S1
- 以不同的视角观察球面x^2+y^2+z^2=r^2和圆柱面x^2+y^2=rx所围区域
MYMIMO
- 文件来源: 我的毕设 仿真结果: 在窄带Rayleigh快衰落信道下几种检测方法的误码率性能比较 说 明: 参数tx,rx,L,EbN0可以根据需要更改。 tx,rx是收发天线数,根据需要取值就好了,一般研究2发2收和4发4收 EbN0是信噪比取值范围,根据需要选择吧。取得点多当然算得慢。 L影响结果的波动性和误码率所能达到的下限,L值取得越大图像越接近真实情况。如果 EbN0最大值有20dB那么误码率可以达到
channel
- ofdm信道特性 Channel transmission simulator Channel transmission simulator % % inputs: % sig2 - noise variance % Mt - number of Tx antennas % Mr - number of Rx antennas % x - vector of complex input symbols (
Newton 插值程序
- 本程序的要求是已知几个节点x及节点函数f(x),要求近似函数!只要输出每点函数,对角线上的值,和最后一行的值,为继续插值准备! 例如:0.00 0.00000 0.20 0.20134 0.30 0.30452 0.50 0.52110 得到结果:0.00000 0.20134 1.006700 0.30452 0.083666 0.52110 1.082900 0.170333 0.173334 f(0.230000)=0.24933
rx
- 这个程序是控制无线模块2401接受,为51系列单片机控制。可以将接收到的字节上传到电脑的串口