搜索资源列表
spidmadriver
- 本驱动程序在linux2.6.17中测试通过。yangxing msn:lelma_yx@hotmail.com 希望对SPI操作的朋友有所帮助。 一、工作方式: 从设备:SPI为MASTER模式 S3C2410:SPI为SLAVE模式+DMA 二、工作流程 1.S3C2410从接收:当从设备发送数据时,S3C2410利用DMA方式收数,收到指定长度的数据,则进入DMA中断,将接收的数据拷出。 2.S3
build-arm-linux-3.4
- arm linux交叉编译环境的搭建,针对gcc 3.4版本。
摄像头抓图程序
- ARM的USB视频采集源程序 抽取出来了三个文件:vidcat.c v4l.c v4l.h 搞定了它的编译,生成了一个60k的vidcat可执行文件,拷贝到2410上后工作正常-Video capture source program of ARM USB draw following 3 file: vidcat.c v41.c v41.h to finish its compile and build about 60K
busybox-0.60.2
- 为samsung2410 ARM移植的busybox工具包,用作嵌入式linux的命令行接口-for samsung2410 ARM transplant busybox Kit linux for the embedded command line interface
LPC_ARM_KEIL_RV_DEMO
- LPC23XX ARM的驱动程序库,开发环境为KEIL RV。做LPC23XX程序时可以直接应用-LPC23XX ARM driver library, development environment for the KEIL RV. Do LPC23XX procedures can be applied directly
lwip-1.3.0
- ARM TCP/IP LWIP最新版本1.30-ARM TCP/IP LWIP the latest version 1.30
tree
- Linux下的tree命令,同window,功能更强大! 1、下载tree-1.5.1.1源程序 2、解压源码到工作目录tar zxvf tree-1.5.1.1.tgz 3、在tree-1.5.1.1目录交叉编译:make CC=arm-linux-gcc 4、安装:make prefix=/home/xxxx/rootfs install Ubuntu下 直接 apt-get install tree 即可
ADSARM
- ARM编译指南,包括基本操作,开发步骤等,很好用-ARM compiler guide, including basic operations, the development of steps and so on, very good use
05
- 程序代码使用说明: (1)所有源代码目录下都提供了Makefile(非Qt),或者.pro(Qt),或者更详细的说明(第7章)。作为对比,也可以参考在书中的对应章节采用直接gcc命令的编译方法,来学习如何编写Makefile。 (2)Makefile中默认情况下采用“CC=gcc”或者“CPP=g++”的设置,交叉编译时请使用“ make CC=arm-linux-gcc CPP=arm-linux-g++”(假设你使用的
s3c2410_ts
- 本源码是《ARM嵌入式LINUX设备驱动实例开发》一书的触摸屏设备驱动源代码-The source is ARM Embedded LINUX device driver examples of development of a book on touch-screen device driver source code
2410pcb
- 2410开发板pcb图,源自freindy arm(友善之臂)-2410 development board pcb diagram
gpio-test
- 1、将makefile中的 CROSS =/usr/local/arm/2.95.3/bin/arm-linux- CFLAGS+=-I/usr/local/src/2.4.18-rmk7/include CFLAGS+=-I/usr/local/src/2.4.18-rmk7/include/linux CFLAGS+=-I/usr/local/arm/2.95.3/arm-linux/include 路径改为你
ftpd_FTP_Telnet
- busybox-1.14.2+wu-ftpd-2.6.2实现FTP和Telnet移植详解 平台:Ubuntu8.10 交叉编译器:arm-linux-gcc 3.41 文件系统工具:busybox-1.14.2 ftp移植软件:wu-ftpd-2.6.2 相关软件: bison-1.35. netkit-base-0.17 移植目标:arm2440开发板-busybox-1.14.2+ wu-ftpd-
iso7816-3
- 智能卡接口控制器源代码,符合ISO7816-3的协议要求-Smart card interface controller source code, in line with the ISO7816-3 of the agreement called for
QTE4.5.2_2410
- 开发环境: QTE4.5.2移植到2410过程 操作系统:Vmware6.5+ubuntu 8.04 交叉工具链:arm-linux-gcc-3.4.1 目标:GEC2410+NEC 3.5寸 -Development Environment: QTE4.5.2 transplanted to 2410 the process of the operating system: Vmware6.5+ ubuntu 8.
libgcc_s.so.1.tar
- linux库 arm-linux-gcc 4.3.2 里面的库,是x86版本的-linux libraries arm-linux-gcc 4.3.2 inside the library, is the x86 version
LPC3250_u-boot-1.3.3.tar
- NXP公司的ARM9 (LPC3250)下,绝对可用的uboot 源代码。网络、sdram、flash等一切正常。而且非常可靠。u-boot 的版本号是:1.3.3 .用ARM-linux-gcc 编译。-NXP' s ARM9 (LPC3250), the absolute uboot source code available. Network, sdram, flash and all is normal. And very
arm-linux-gcc-3.3.tar
- 本代码是基于linux嵌入式的交叉编译器,已经配置好了,适合大多数用户尤其是初学者对交叉编译环境还很陌生的同学-This code is based on embedded linux cross compiler has been configured, for most users, especially beginners cross-compiler environment are still unfamiliar with t
3.4.1.tar
- arm linux gcc 3.4.1 version
lib
- openCV3.3在Ubuntu 16.04下用友善之臂的arm-linux-gcc-4.5.1编译的,需要的可以下载(OpenCV3.3 is compiled with a friendly arm of arm-linux-gcc-4.5.1 under Ubuntu 16.04 and needs to be downloaded)