搜索资源列表
18F2550TEMP
- pic 18f2550 blink led template
test_led
- Blinking a led for PIC 12F675
Buzzer
- A demo program for AT89S52-gLCD-STK1 board with 3.3V regulator & 89C51RB2-IM mcu * to blink an LED at ~10Hz by software delay * && using timer 2 to generate a single tone by the Buzzer connected to Pin P1.0.
blink_LED
- led blink program which is based on 89c51rd2.
winampgccj
- 用线程的方式重新写了一下,移动的效果好了,但是还有点闪烁! 应该采用一些方法能不闪烁,现在已经是画在bitmap上,最后再画到image上的 不知道大家还有什么好的方法,请告诉我! 另外就是在线程画和控件自己刷新之间可能有冲突,而且有写东西的创建和释放有点问题,可能导致winamp死掉! 使用方法:歌词文件和歌曲文件同名在同一个文件夹下! 试了一下winamp5也是可以使用的!-Way to use threads
cx
- 51单片机的外部中断1引脚接开关K1，外部中断引脚0接开关K0，P1.0～P1.7分别接八个发光二极管，开机后只有一个发光二极管从左到右每隔0.5秒循环移动点亮。 当K1电平产生电平跳变时，二极管的循环移动发光被停止，取而代之的是黄色二极管5秒间的闪烁，闪烁频率为0.5秒，5秒钟过后，八个发光二极管恢复到原来的循环发光状态。 当K0电平为低电平时，无论是二极管处于循环移动发光状态，还是处于黄色二极管的5秒间闪烁状态，都应被强制中
blink
- ARM processor s basic proteus model
blinky
- blink project atmega16
FriendlyARM_GPIO
- Source code written in C to gain access to GPIO pins of the FriendlyARM (mini2440) development board. Source code will blink LED1 on FriendlyARM every second.-Source code written in C to gain access to GPIO pins of the F
LCD_Blinky
- MCBSTM32C blink LCD sample code keil
Blink
- 基于nesC的无线传感器网络节点led灯的闪烁-NesC-based wireless sensor network node led flashing light
qicheweideng
- 假设汽车尾灯左右两侧各有3个指示灯，要求：汽车正常行驶是指示灯全灭 右转弯时，右侧3个指示灯按右循环顺序点亮：左转弯时，左侧3个指示灯按左循环顺序点亮 临时刹车时所有指示灯同时闪烁。-Assumptions about car tail lights on each side of three, asked: car traffic is light Quanmie normal turn right, press the right
Animated_C2123858182008
- Usually we see static Captcha, now we will make an imated Captcha. Now this cool. What does the captcha look like? It just like the ordinary Captcha, the difference is the letters are moving and animated. You can set yo
LPC2368UCOS_LED
- uCOS-II 2 uC-OSView led blink.rar
zuoyi
- 通过按键进行控制发光二极管的左右移动和闪烁-Through the LED control button and move around and blink
microtouch1v2
- New in 1v2 Updated with the actual files to support the internet demo -) Support for SSD1297 LCDs. These are found in a number of touch LCD players, including the first version of the Sylvania player. They are mark
Jimbo-Nokia-SAM7-Example
- Led blink on a LPC2103
ledblink
- For non-embedded programmers the first thing to try on a new system or in a new programming language is to print out "hello world". The equivalent for microcontrollers and other embedded systems is to blink a LED. When e
LED_BLINK
- this an ARM 2148 program to make the LED of the device to blink depending on delay -this is an ARM 2148 program to make the LED of the device to blink depending on delay
test_pic16f4550
- PORTB blink leds..Set PortB as output.. The start programme for assembly language in pic18f4550