搜索资源列表
stepper.tar
- linux下 步进电机驱动，C 语言源代码-stepper motor drives, C language source code
驱动
- 用Keil C51写的步进电机驱动程序。-Keil C51 was made with the stepper motor driver.
步进电机驱动
- 提供的程序是供四相步进电机使用。本实验使用的步进电机用直流+12V电压，电机线圈由A、B、C、D四相组成。 2. 驱动方式为四相单四拍方式,各线圈通电顺序如下表。表中首先向A相线圈输入驱动电流，接着向B，C，D线圈通电，最后又返回到A相线圈驱动，按这种顺序轮流切换，电机轴按顺时针方向旋转。若通电顺序相反，则电机轴按逆时针方向旋转。-provide for the procedures of the four-phase stepper
stepper
- 一种新的控制步进电机的方法。基于8279的键盘和显示器控制。-A new way to control stepper motors. Based on 8279 s keyboard and display control.
STEPPER-SOFT
- 步进电机驱动程序,MCU:AT89C51,硬件L297,L298.-Stepper motor driver, MCU: AT89C51, hardware L297, L298.
stepper-motorcontrolwithMCS-51
- 以四相步进电机为例,介绍了由MC1413 驱动的电路原理图,给出了四相步进电机的正 转反转的程序设计流程图和程序清单。-To four-phase stepper motor as an example, the introduction of the MC1413-driven by the circuit schematic diagram is given four-phase stepper motor is to reve
stepper-motor
- 本程序用于51系列单片机对步进电动机的控制，具有可实现性。-This procedure for the 51 Series Single-chip stepper motor for control can be achieved with sexual.
Stepper(STK672-050)
- 基于STK672-050（3A）驱动的步进电机C51源码-Based on the STK672-050 (3A) of the stepper motor-driven source code C51
Stepper
- stepper motor controller using vb through parallel port
stepper
- 步进电机stepper.c可以用的-Stepper.c This is Stepper and proteus!!!
stepper
- Stepper Motor to control the direction
stepper
- AT89S52控制四相步进小电机正反转示例程序-AT89S52 control small four-phase stepper motor positive sample procedures
stepper
- these are the codes made on labview 8.0 for driving stepper motor for different speed profile.
Stepper.motor.machine.c
- 步进电机该机c编程设计代码Stepper motor machine code c Programming -Stepper motor machine code c Programming
stepper
- 步进电机驱动在linxu下面的运行。描述操作系统的启动运行-Stepper motor drive is running in the linxu below. Descr iption of the operating system up and running
Motor-Stepper
- 单片机控制步进电机正反转。Proteus仿真。C语言编写。-51 MCU with stepper motor control in C language.Proteus simulation .
all-about-stepper-motors
- Stepper motors are DC motors that move in discrete steps. They have multiple coils that are organized in groups called "phases". By energizing each phase in sequence, the motor will rotate, one step at a time
Stepper Motor
- EMBEDDED C PROGRAM TO INTERFACE STEPPER MOTOR WITH ARM7
stepper motor driver
- stepper motor drive. use VHDL
stepper
- stm8 stepper motor control