搜索资源列表
PICsond
- PIC单片机 串口发送 AY命令源代码 C程序-PIC SCOND
tcom
- IBM-PC汇编语言开发的串口通讯程序。能够发送/接收字符信息和文件。-IBM-PC assembly language development of serial communication program. Able to send/receive character information and documentation.
51
- 51单片机C语言程序，即串口-发送反馈程序-51 Microcontroller C Programming Language, that is, the serial port- Send feedback process
DS18B20
- AVR单片机 Atmega128获取ds18b20温度传感器数据并通过串口发送该数据的程序 硬件调试通过-AVR microcontroller Atmega128 temperature sensor data and obtain ds18b20 send the data via the serial port hardware debugging through the procedure
labwiew_port
- 一个labwiew串口通信程序，可以实现上位机向单片机发送数据并接受从单片机传送来得数据。-this is a labview program,and it is a port selver.
shangweiji
- 本上位机是基于VB语言编程的进行与单片机串口通信的上位机。用于三个舵机的控制。串口通信格式为波特率9600bps、8位数据位、1位停止位、无校验、ASCII码字符通信。串口通信程序用于接收上位机发送过来的控制命令。控制命令采用自定义文本协议，即协议内容全部为ASCII码字符。通信协议格式为起始符“#”通道号CHx，脉宽百位，脉宽十位，脉宽个位，与停止符“!”。-The host computer is based on the VB p
Uart2
- 串口通信程序，包括读取中断、解读和发送程序，代码已经通过测试！-Serial communication program, including reading the interrupt, read and send the program, the code has been tested!
pc_pc
- 本人编写的针对dsp的flash的在线烧写程序，也可以当做简单的串口调试程序使用。发送数据使用的是串口，用到软硬握手，希望大家指教-I prepared for the dsp to flash online programming process, as a simple serial port can also be used by the debugger. To send data using the serial port,
UartOfSound
- 串口发送和接收数据的程序。当接收到某一数据时发出报警声音。-Serial port to send and receive data through. When receiving a data alarm sounds.
comm_port_source_project
- 完整的串口小程序，可以通过设置串口端口及波特率，实现发送与接收，同时可以设定超时。-A whole comm project,it can receive and translate by setting comm port and baud rate.It can also set time out reminder.
Comm_borlandC_source_project
- 使用Borland c++编写的串口收发程序，通过设置端口及波特率实现接收发送-It is use Borland c++ to programme and it can achieve the comm port receive and translate.
chuankou
- 单片机与pc机串口数据通信 利用可视化程序设计编制串口调试软件，然后向串口发送“1”、“2”、“3”......“8”、“9”、“0”等字符，实验板收到数据后通过数码管显示出来，同时会向PC机反馈显示成功的确认信号，即在PC机串口调试软件的接收缓冲区内将显示“display OK！”等字样。-Single-chip data communication with the pc serial port using visual pro
Send
- 恒流源测试程序，该软件是用串口发送数据，测试恒流源-Constant current source test program, the software is to use the serial port to send data to test current source
Serial-data-communication
- 安装虚拟软件，该程序能将A/D转换值和电压值，不仅在lcd上显示，而且还能通过串口发送到上位机pc中。-Install virtualization software, the program can A/D conversion value and voltage value, not only in the lcd display, but also sent to the host computer via serial port
chuankou
- 利用汇编语言编写的串口通信程序，可发送数字并显示在接收端的数码管上，用PROTEUS7仿真，测试通过，运行良好-Written in assembly language using serial communication program, the number can be sent and displayed at the receiving end of the digital control, and with the PROT
gsmGPS
- 51单片机串口读取GPS信息，然后通过串口发送到GSM网络的程序，调试通过可用-failed to translate
smart
- 本程序是基于LABWINDOWS/CVI 的，主要是通过串口采集下位机信息，然后显示状态信息并通过串口发送命令字节。-The program is based on LABWINDOWS/CVI.It get message from RS232and display status,then send command by RS232.
lesson10_UART
- 基于AVR-mega16的串口发送接收程序。-The UART program base AVR
UART_TX
- 通过FPGA串口发送到电脑的 HELLO WORLD 程序，成功调试，可以下载到板子上运行-This can sending the HELLO WORLD through the FPGA to computer ,you can launch the code on your board.
PC-and-MCU-Serial-Communication-2
- 单片机与PC串口通信程序，通过PC发送的指令来控制蜂鸣器和数码管-MCU and PC communication