搜索资源列表
dp51e
- 通过串口，接收上位机发送的命令，并进行CSI24WC02的读写操作，并返回相应 数据或应答。用汇编实现,可以用keil编译器-through the serial port, the receiving PC to send orders, and CSI24WC02 read and write operations, and return to the corresponding data or response. Assemble
汇编串口
- 本程序是通用同步和异步串行接收器和转发器(USART)在异步状态下使用中断 * 方式进行全双工接收和发送数据的通信程序。共包括下面列表中这四个子程序。这 * 四个子程序的具体使用方法请参考各自的说明。-this procedure is common synchronous and asynchronous serial receivers and transmitters (USARTs) in the state to use as
receiveb
- VB串口通信之串口接收程序。采用MSCOMM控件编程实现-VB serial communications serial receiving procedures. Using MSCOMM Control Programming
vcom
- 一个2000系统上的虚拟串口驱动程序，目的是解决已有只能从串口接收数据的程序能够接收来自其他端口的数据。-a system of virtual serial port driver, has been designed to address only receive data from the serial port procedures to receive from other ports of data.
mscommcon
- 通过串口发送和接收数据,界面简单漂亮.很容易的一个程序-through the serial port to send and receive data, interface pretty simple. A very easy process
moder
- moder 51汇编程序框架 D4为串口发送中断指示灯； D5为外部中断1指示灯； D6为外部中断0指示灯； D7为串口接收中断指示灯； D8为定时器指示灯；-moder 51 D4 Series procedural fr a mework for the serial interrupt this light; D5 for external interrupt a lamp; D6 for external
tutorial-telcom
- 网络传来的控制命令经过网络接口转发到串口，中控主机通过串口接收命令进行操作，并且设置 IP 地址、网关地址和分组号都是通过串口进行的，因此串口调试是监控程序调试的第一步。-network control commands sent through the network to transmit serial interface, China controlled by the mainfr a me to receive orders
PCMtoWave
- 录制和播放wav文件，显示波形，并能够通过串口接收pcm语音数据，转换为wav文件播放-recording and playback wav documents, waveform, and through the serial data receiver pcm voice, Converting to wav Player
master-meter-V_01
- 此源码为商用的电力抄表系统的主机端源程序。通过电力载波模块，由51单片机的串口接收并控制从机的抄表。-this source for the business of the electricity meter reading system mainfr a me terminal source. Through the power line carrier module, from 51 MCU serial reception fro
dingshibiangejisuan
- 利用51单片机计算双字节的定时器数据 at89c2051就可以用 生成查表用的数据 数据经串口送到电脑，用串口接收软件接收 白菜奉献-calculated using the double byte data at89c2051 timer can be generated on the use of look-up table the data to the computer via serial port,
AV_TXDGPS_060627_4800bps
- 串口接收GPS NMEA数据RMC串，解出经纬度速度GPS状态等信息后，通过无线模块发送到接收机-serial GPS receiver NMEA data RMC series, to come up with the speed of GPS coordinates for the state, and other information, Wireless sent to the receiver module
PIC_STUDY
- 完整的PIC学习程序示例 软件功能： RT1602C驱动 UART串口输出，波特率为19200 按键扫描： 键1控制LCD的显示状态，接收状态或是发送状态 键2循环控制UART将要输出的子串口 AD转换功能 UART串口接收中断 TIME1定时器中断 具体请参考硬件连接图-integrity of the learning process software examples : RT1602C
GPS-chuankou
- 通过本程序，实现通过串口接受GPS接收机信号，并显示纬度、经度、航速等信息-through the procedures, accepted by serial GPS receiver signal, and display latitude, longitude, speed and other information
VB_recevier
- 自己做的VB串口接收程序，用的MSCOMM实现。-own VB serial receiving procedures, the MSCOMM achieve.
comdraw
- 串口发送接收数据。可配置端口，波特率等。 发送可选择ASCII方式或HEX方式。 中断方式接收数据。 可以通过ADC和MCU可以把数据通过 串口直接发送到PC上让MATLAB分析-receiving data. Configurable ports, baud rate, and so on. Send option HEX or ASCII mode. Interrupt receiving data. Thro
051205-firmware
- MSP430和GPS的接口程序，通过MSP430的串口接收GPS发出的数据-MSP430 and the GPS interface procedure for the adoption of the MSP430 serial GPS receiver data issued
Fre_labview
- LabView平台下的频率计算显示程序，通过串口接收下位机的数据，并进行测频过程的控制，完成计算和显示。-LabView platform frequency calculations show procedures, through the serial port to receive the next bit plane data, and frequency measurement process control, complet
RS232_VB
- 串口接收发送调试程序，简单实现串口通信 串口接收发送调试程序，简单实现串口通信-Serial receiver to send debug procedures realize a simple serial communication serial port to receive send debug procedures realize a simple serial communication
RS232-I2C
- 该程序利用单片机完成数据在串口与SMBus总线（即I2C）之间的转发，即将串口接收到的数据通过I2C转发出去，将I2C接收到的数据通过串口转发出去-Completion of the program using single-chip data with the SMBus serial bus (that is, I2C) between the transponder, is about to receive serial data
GPS
- 通过串口接收GPS数据，进行数据提取显示保存。-Through the serial port to receive GPS data show the preservation of data extraction.