搜索资源列表
sys(matlab)
- 某控制系统的开环传递函数的分析.绘制系统的闭环根轨迹，寻找系统临界稳定时的增益k，并分析其稳定性。-a control system of open-loop transfer function analysis. Rendering System is a closed-track, Find Critical stable gain k, and to analyze its stability.
kongming
- 神经网络训练根据Kolmogorov定理，输入层有14个节点，所以中间层有29个节点 ％中间层神经元的传递函数为 tansig ％输出层有8个节点，其神经元传递函数为logsig ％训练函数采用traingdx-neural network training under the Kolmogorov theorem, input layer has 14 nodes, Therefore, the intermediate
cpid4
- 针对带时滞二阶振荡环节的系统传递函数,我们这里研究了,二阶振荡环节时间常数增大,对系统动态性能的影响,读者可以在程序上对时间常数进行修改,即可得出比较与区别.-brought against Delay second oscillation link system transfer function, we studied here, and the second time constant oscillation links incr
函数传递数组的方法
- 多维数组（二维以下和数组）在内存中也是按顺序存放的，因此也可以用这种方式传递。但是，如果要确切知道每个元素在数组中的位置，就应给出各维的最大索引值-multi-dimensional arrays (two-dimensional array and below) in memory is stored sequentially, so you can pass this way. However, if we know exactly
Mseires
- 用MATLAB产生M序列作为系统的输入，根据传递函数，仿真输出，并得出输入的自相关函数和输入输出的互相关函数。-M sequence generated by MATLAB as input, in accordance with transfer function, simulation output, and come to enter the auto-correlation function and the input and
fifteen
- 闭环控制系统输入信号为阶跃信号，受控对象的传递函数为3 2 1 ( ) 2 5 s G s S s s 。-Closed loop control system for the step input signal, the transfer function of the controlled object 3 2 1
Mxulie
- 产生M序列，可以作为系统的输入，经过系统辨识后得到输出，进而得到系统的传递函数-M sequences generated can be used as the input, output obtained through system identification, and further to the transfer function
xiangguanfabianshi
- 利用M序列作输入估计脉冲响应值，完成对连续和离散系统传递函数参数的辨识-Use of M sequence as the input impulse response estimated value to complete the continuous and discrete transfer function parameter identification
matlab-linear-system-analysis
- matlab线性系统分析,传递函数模型,质量－弹簧－阻尼系统,零极点增益模型（连续系统）-matlab linear system analysis, transfer function model, mass- spring- damper system, zero-pole-gain model (continuous system)
Distributed Tansfer Function Method
- 利用分布参数系统的传递函数法对带有扩展层的约束阻尼梁进行编程分析，得到频率响应曲线，并获得位移峰值对应的频率，即固有频率。(The transfer function method of distributed parameter system is used to analyze the constrained damping beam with extended layer, and the frequency response c
VB中用户自定义类型参数的传递方法
- 本文以Info-ZIP公司的unzip32.dll动态连接库中的函数Wiz_UnzipToMemory为例，详细讨论了在VB中使用Wiz_UnzipToMemory函数时正确传递用户自定义类型参数的方法。(This article takes the Wiz_UnzipToMemory function in the unzip32.dll dynamic link library of Info-ZIP Corporation as
chord measurement
- 三点偏弦测法理论说明文献 弦测法传递函数及黄金分割点遍历程序(Theory and Research of Asymmetrical Chord Offset Method)
辽宁某学院模糊pid仿真
- 这是我根据百度文库中一片辽宁某学院的本科毕设论文还原的二阶传递函数模糊pid控制、pid控制的代码。真实有效。(This is the two - order transfer function fuzzy PID control and PID control code that I have reduced according to an undergraduate thesis of a Liaoning college in t
clab3mixed
- 控制工程，simulink仿真，根据一特定传递函数画图仿真(Control engineering, Simulink simulation, according to a specific transfer function drawing simulation)
question1
- 编制阶跃响应与方波响应相互转化的程序、由阶跃响应数据获得对象传递函数模型的通用程序、由阶跃响应数据获得对象微分方程模型的通用程序。并通过一个传递函数进行验证（阶跃响应和方波响应数据可利用simulink生成）(A program for converting step response to square wave response, a general program for obtaining transfer function m
PLL_system_cal&jitter_cal
- 计算PLL环路的传递函数，环路带宽，相位裕度等参数； 根据相位噪声大致估算对应的输出信号的jitter(calculate the transformer function, bandwidth, phase margin .etc; and calculate the jitter from phase noise;)
振动当量模型传递函数计算
- 利用matlab对轴系当量模型扭转振动的振型和频率进行计算(Calculation of torsional vibration modes and frequencies of shafting equivalent model by MATLAB)
此matlab程序用来模拟仿真光学系统的传递函数（MTF），将MTF进行参数化处理
- 此matlab程序用来模拟仿真光学系统的传递函数（MTF），将MTF进行参数化处理
zuixiaoercheng
- 两种对二阶系统进行参数辨识的最小二乘算法，一种可以直接得到输入输出之间的传递函数，一种可以解出线性的差分方程各系数，再反解得到传递函数。附带的一个二阶系统的模型，可以自行下载导入输入输出数据进行试验。(Two kinds of least square algorithm for parameter identification of second-order system, one can directly get the trans
符号多项式转传递函数
- 可以将符号表达式转为传递函数，并通过赋值可以绘制伯德图