搜索资源列表
msp430的四种计时器程序
- msp430的四种定时器程序。。。。。。。。(MSP430 four kinds of timer program)
定时器产生延时通7秒断13秒程序
- c语言程序实现定时器产生延时通7秒断13秒的小程序(C language program to achieve a timer delay, 7 seconds to break 13 seconds of small procedures)
定时关机
- 完成定时关机的程序，基于C++builder软件编写(Completion of the shutdown program)
AVR单片机定时器
- 采用ATmega16的单片机定时器程序，使用中断方式(this is a Timer designed with Atmega16)
用定时器控制指示灯
- 此程序是nrf52832系统的小程序，作用是用LED显示定时器运行状态。(This program is a small program nrf52832 system, the role is to use LED to display the timer running state.)
定时关机程序
- 这个程序虽然实用价值不大，但是可以让我们了解函数。(Although this program is practical and of little value, it can give us an understanding of functions.)
定时器
- 用STM32F103C8T6芯片完成定时器功能。主要是一些配置可以参考，还有注意中断服务程序。(Use STM32 chip to complete timer function)
V10与中控指纹通用接口程序
- 中控指纹考勤机与V10接口, 设置指纹机数据接收方案，及卡号上传方案，由此服务程序定时处理数据同设备间交互(zksoft fingerprint attendance machine and V10 interface, The data receiving scheme of fingerprint machine and the program of card number uploading are set up, so th
例5-3 使用定时循环产生波形
- 使用定时循环产生波形,程序为《labview2015程序设计从入门到精通》内的例程，labview2015编译环境下编写的程序，对初学者很有用(The use of timing cycle to generate waveform, the program for "labview2015 programming from entry to master" routines, labview2015 compile
STm1.3程序
- 通过stm8的定时器进行计时，将数据存储到EEprom里面，通过定时器进行按键检测(Timer through the stm8 timer, the data stored in the EEprom, through the timer button detection)
定时自动关闭开关功能
- 该程序用于工程中自动控制系统，设定开启时间，当到达指定时间时程序自动停止，该程序定时功能不影响外部定时循环。(A LABVIEW PROGRAM YOU MAY USE)
实验18：定时器1中断
- 51开发板中第10个定时器中断，运行程序后会自动运行相关程序(The 10 timer interrupts on the development board, and the program will run automatically after running the program)
ofdm符号定时与频偏联合估计算法matlab实现
- ofdm符号定时与频偏估计的Matlab实现程序(Matlab implementation program for OFDM symbol timing and frequency offset estimation)
ALIENTEK MINISTM32 实验7 定时器中断实验
- 基于STM32F103RCT6mini开发板定时器中断上更改的HC-SR04超声波程序，亲测可用(The HC-SR04 ultrasonic program based on the STM32F103RCT6mini development board timer interrupts changes, and the pro test is available)
Schmidl&Cox定时同步
- 利用SC算法编写的基于训练序列的定时同步程序(Time synchronization program based on training sequence based on SC algorithm)
STM8S105定时器2精确延时
- STM8S105的定时器2的精确延时程序(STM8S105 timer 2 precise delay program)
在UNIX操作系统下实现定时自动运行指定程序的方法
- 本文详细讨论了UNIX操作系统下实现定时自动运行指定程序的方法，该方法已经在银行网络设备管理中得到实际应用，取得很好效果。(This article discusses in detail the UNIX operating system to achieve the scheduled automatic operation of the specified procedure, the method has been in the
一个可设置时间的倒计时定时器（0到99）
- 通过按键k1到k6实现设置定时器的时间设置，并且启动倒计时。当倒计时到达0时自动报警3次(Set timer time Settings by keystroke k1 to k6, and start the countdown. Automatic alarm 3 times when the countdown reaches 0)
通用定时器(Timer)
- 此为ARM1138开发板的几个关于通用定时器的范例程序，包括32位/16位单次触发定时，32位/16位周期定时/RTC定时，PWM应用等。(This is a few examples of general timer for ARM1138 development board, including 32 bit /16 bit single trigger timing, 32 bit /16 bit cycle timing /RT
STM32定时器中断程序
- 本源代码为讲解基于STM32的定时器中断程序，通过定时器TIM3产生间隔1秒钟一次的中断，在中断中控制LED发光二极管，每次中断都使发光二极管状态取反(This source code is explained based on the STM32 timer interrupt program, through the timer TIM3 interrupt an interval of 1 second, in the inter