搜索资源列表
遥控器I2C
- 遥控器编码的c51程序,包括遥控器编码,I2C操作编程等-remote coding decoder procedures, including remote control codes, such as I2C programming operation
REMOTE_IR
- 一个使用8051单片机接受遥控器编码的例子-8051 using a remote control device to accept the code examples
newLEDdisplay
- 一个非常好的微处理器检测遥控器编码的C++ 原代码项目文件,直接可用,LED显示-a very good microprocessor remote detection coding in C source code, project documentation, direct can be used, LED Display
origin_LEDdisplay
- 一个非常好的微处理器检测遥控器编码的C++ 原代码项目文件,直接可用,LED显示,成果真诚奉献-a very good microprocessor remote detection coding in C source code project documents directly available, LED Display, results sincere dedication
ir32b02
- 实用遥控器编码程序1-Useful encode program 1 of remote controller
388
- H388红外遥控器编码,有利于将要或正在开发遥控产品的朋友
IR-LED
- 红外键值码LED显示,用于C51程序,解码遥控器编码
text
- 模拟遥控器编码，可是模拟三个按键的编码，用c语言编写。
ir32b02
- 实用遥控器编码程序1-Useful encode program 1 of remote controller
遥控器I2C
- 遥控器编码的c51程序,包括遥控器编码,I2C操作编程等-remote coding decoder procedures, including remote control codes, such as I2C programming operation
REMOTE_IR
- 一个使用8051单片机接受遥控器编码的例子-8051 using a remote control device to accept the code examples
388
- H388红外遥控器编码,有利于将要或正在开发遥控产品的朋友-H388 IR remote control codes, has to be conducive to the development of remote control products or are friends
IR-LED
- 红外键值码LED显示,用于C51程序,解码遥控器编码 -IR key code LED display for the C51 process, decoding the remote control code
jiema
- 本程序为红外遥控器的解码程序，可以通过调试本程序，得到各种红外遥控器的按键编码，以方便用户使用-This procedure for the infrared remote control decoding procedure can debug the process, access to a variety of infrared remote control key codes, to facilitate users
89s52_11m_sony_nec_e2rom
- 单片机红外遥控开关，能读取SONY和NEC两种红外遥控器编码，学习后就可以用任意遥控器遥控某些设备开或关，汇编语言编制-Single-chip infrared remote control switch, SONY and NEC can read two infrared remote control codes, learning can be used after any remote control on or off cer
remote
- 9E利普,东芝等6种红外遥控器编码及程序
Study_IR_Remote_Control
- 资料包含源码，硬件图，红外相关资料等，本学习型红外遥控器，通过学习一次遥控器的编码，即可脱离原遥控器来遥控电器或者设备，源码很完整，严格测试过，不过由于C52的单片机RAM有限，编码缓冲区长度有限，而不同的遥控器的编码长度也不相同，对于像空调遥控器编码比较长的就会出现学习不了的情况，必须要加外部RAM作为接收缓冲区，或者换用STC的单片机，内部的RAM比较大，不用扩展，用STC还有好处就是不需要外部的eeprom来保存读取的编码，而C5
遥控器编码电路
- 该代码根据时序图，采用verilog代码实现了遥控器编码电路的功能。(The code according to the timing diagram, using Verilog code to achieve the function of the encoding circuit of the remote controller.)
遥控器接收解码电路
- 设计遥控器接收解码电路。该电路接收编码后的串行数据，解码输出数据。电路接收 到的串行数据的格式为： 4 位同步码“ 1010”， 4 位数据（高位在前）， 1 位奇校验码（对前 8 位数据校验）(Design of remote control receiver decoding circuit. The circuit receives the encoded serial data and decodes the output d
软件延时
- NEC协议的红外遥控器编码解码程序，大家收集到的通常是采用定时器中断的方式，我这个代码是采用软件延时的方法实现的，能省掉单片机的一个定时器中断源，一直运用于项目上。(NEC protocol's infrared remote control coding and decoding program. We usually use the way of timer interruption. My code is implemented