搜索资源列表
基于FPGA的128细分的步进电机驱动程序
- 基于FPGA的128细分的步进电机驱动程序
驱动
- 用Keil C51写的步进电机驱动程序。-Keil C51 was made with the stepper motor driver.
步进电机驱动
- 提供的程序是供四相步进电机使用。本实验使用的步进电机用直流+12V电压，电机线圈由A、B、C、D四相组成。 2. 驱动方式为四相单四拍方式,各线圈通电顺序如下表。表中首先向A相线圈输入驱动电流，接着向B，C，D线圈通电，最后又返回到A相线圈驱动，按这种顺序轮流切换，电机轴按顺时针方向旋转。若通电顺序相反，则电机轴按逆时针方向旋转。-provide for the procedures of the four-phase stepper
直流电机
- 次程序为单片机89S52系列直流电机驱动程序,具体解释见程序.-meeting procedures SCM 89S52 series DC motor drivers, specific explanation procedures.
4-6line-asm
- 4相6线步进电机程序，用于测试步进电机，驱动采用反向驱动-4-phase stepper motor 6-line procedures for testing stepper motor, drive the use of reverse drive
stepmotor1
- 步进电机程序，用l297 l298作为驱动电路的，程序比较简单，但是能对mcs-51中断有个详细认识-Stepper motor program l297 l298 as a driving circuit, the procedure is relatively simple, but can be interrupted for mcs-51 has a detailed understanding of
L298
- L297,L298驱动步进电机程序，能通过按键控制电机正反转-L297, L298 stepper motor-driven process, through the buttons to control the electrical positive
stepper
- C51驱动四相步进电机程序，用的是AT89C51-C51 four-phase stepper motor-driven process, using AT89C51
STmcuCmotordrive
- ST单片机C语言驱动电机程序,实现电机的正转、反转、停止等功能。-ST Single-chip C-drive motor procedures to achieve motor is, reverse and stop functions.
BJDJ-C
- 51单片机步进电机程序驱动，适用步进电机控制模式！-Keil-51C
StepMotor1
- 这是一个控制两个步进电机的程序，可以作为小车的驱动电机程序，实现正、反转、转弯等功能-This is a stepper motor control of the two procedures can be used as the drive motor vehicle procedures, implementation is, reverse, turning and other functions
L298_motor
- L298N驱动直流电机程序，C语言，编译环境keil，mcuAT89S52，调试仿真实测通过。-DC motor driver L298N process, C language, compiler environment keil, mcuAT89S52, measured through the simulation debug.
Step_motor
- 单片机驱动步进电机程序，keil开发 ，c语言，mcuAT89S52,调试仿真实测通过，步进电机为四相步进电机。-Single-chip stepper motor-driven process, keil development, c language, mcuAT89S52, measured through the simulation debugging, stepping motor for the four-phase st
moto
- 单片机驱动步进电机程序设计.含电路图，设计思路，汇编程序。-MCU to drive a stepper motor programming. Including schematic, design ideas, assembler.
steppermotor
- 单片机驱动的步进电机程序，采用C语言编写。-MCU-driven stepper motor program, using C language.
demoSTEP
- 这是一个使用单片机通过NUL2003驱动步进电机程序. 步进电机: 5伏,500MA/STEP,四限四拍. 将步进电机的A B C D四个绕组连接到 S51E板"步进电机"的A,B,C,D,将公用抽头并接在VCC上. 将"控制输入口"的A B C D 接焊盘 P2.3,P2.2,P2.1,P2.0. 将P2.3-P2.0跳帽置焊盘位. -english
DianjiCRL
- 基于stm32f103的2相4线步进电机驱动A3988程序。(A3988 program of 2 phase 4 wire stepper motor driver based on stm32f103.)
L289N驱动程序
- L298N驱动程序书，驱动电机，可驱动多个电机，能实现正反转(L298N driver book, drive motor, can drive a number of motor, can achieve positive and reverse)
基于stm32-CAN控制伺服电机程序
- 使用stm32f407单片机的CAN通信控制驱动电机，并且该程序可以通过红外遥控(CAN communication with stm32f407 MCU is used to control the driving motor, and the program can be controlled by infrared remote control.)
STC15W404AS驱动无感无刷电机程序（调试通过）
- STC15W404AS驱动无感无刷电机程序,电机电流监测，自动调整驱动输出(STC15W404AS drive sensorless brushless motor program, motor current monitoring, automatic adjustment of drive output.)