资源列表

排序选择:

« 1 2 ... .56 .57 .58 .59 .60 163061.62 .63 .64 .65 .66 ... 267458 »

[软件工程DF-and-AF

说明:该程序是使用Matlab仿真协同通信的DF(解码转发)基本性能,基本模型S-R-D三个节点,接收端使用MRC(最大比合并)。固定DF由于SR信道的错误,其性能受到限制,在大SNR情况下不能获得有效分集。而当SR距离足够近的时候,可能获得一定的分集增益。-AF and DF simulation procedure code
<令狐> 在 2025-10-01 上传 | 大小:7kb | 下载:0

[VHDL编程ycbcr-422-to-444

说明:ycbcr 422 to 444格式转换-YCbCr 422 to 444 format conversion
<wangda> 在 2025-10-01 上传 | 大小:1kb | 下载:0

[软件工程abc

说明:基于MATLAB的变电站无功模糊控制系统-MATLAB-based substation reactive fuzzy control system
<陆海> 在 2025-10-01 上传 | 大小:356kb | 下载:0

[VHDL编程tiqutest

说明:对于信号发生器给出的方波信号作为待处理的信号,通过程序可以提取第一个脉冲,将后面的滤去。注意信号发生器给出的方波幅 值大概在3.3V左右,满足和FPGA的接口电平匹配。-The back of the filtered square wave signal given by the signal generator as a signal to be processed by the program can extract a pulse. Note that the square ampl
<张朗> 在 2025-10-01 上传 | 大小:261kb | 下载:0

[matlab例程youzaosheng

说明:该模型是模拟信号数字传输系统,可以把一个模拟信号通过PCM编码译码,信道2FSK编码译码,再通过一个二进制对称信道,可以恢复出原模拟信号-The model is the analog signal digital transmission system, an analog signal by the PCM codec, channel 2FSK codec, and then through a binary symmetric channel, you can restore the o
<wangpeng> 在 2025-10-01 上传 | 大小:9kb | 下载:0

[通讯编程SCommTest

说明:VC控件MSComm编写串口通信程序  -VC serial communication
<肖凯> 在 2025-10-01 上传 | 大小:1.84mb | 下载:0

[Internet/网络编程wh6[1].6

说明:网狐6.6内核代码, 能编译。 送给需要的朋友-Network Fox 6.6 kernel code can be compiled. To give a friend in need
<name> 在 2025-10-01 上传 | 大小:424kb | 下载:0

[VHDL编程fpga-mcu

说明:利用uart接口,51单片机和FPGA完成16位宽的数据通信,包括数据的幷串转换等。-Uart interface 51 of microcontroller and FPGA 16-bit wide data communications, and including Bing string of data conversion.
<张朗> 在 2025-10-01 上传 | 大小:614kb | 下载:0

[matlab例程gang_gang

说明:该程序是一个完整的模拟信号数字化传输系统的程序,它进过了PCM编码,2FSK调制解调和一个高斯白噪声,并有误码率的测量-The program is a complete program for the analog signal digital transmission system, it been to the PCM coding, 2FSK modem and a Gaussian white noise, and BER measurement
<wangpeng> 在 2025-10-01 上传 | 大小:2kb | 下载:0

[VHDL编程jishi999999

说明:程序实现6位计数器,000000~999999,有一个使能信号en,将使能信号en由FPGA的引脚68接入,使用信号发生器产生方波,en信号为1的时候计数器计数,对于输入方波的幅值调为3.3V,可发现计数器计数一段时间会停止,然后接着计数。-Program six counters, 000000 999999, an enable signal en enable signal en by the FPGA pin 68 access, using the signal generator t
<张朗> 在 2025-10-01 上传 | 大小:687kb | 下载:0

[Windows CEBthDemo

说明:PDA开发的示例程序,可以用于学习用途,需要的可以下载。-PDA developed sample programs can be used for learning purposes, the need can be downloaded.
<k> 在 2025-10-01 上传 | 大小:42kb | 下载:0

[C#编程picturePane

说明:适用于大文本数据做图,通过选择不同的列生成相应的图片-Figure applies to large text data to generate the corresponding image by selecting different columns
<可爱小迪> 在 2025-10-01 上传 | 大小:939kb | 下载:0
« 1 2 ... .56 .57 .58 .59 .60 163061.62 .63 .64 .65 .66 ... 267458 »

源码中国 www.ymcn.org